Problem No. 2A 250x400mm beam with a concrete cover of 40mm and stirrups of 10mm with fc' of 35Mpa and fy of 276Mpa. The reinforcement used has a diameter of 16mm. Calculate the following. 14. Calculate the maximum moment

Problem No. 2A 250x400mm beam with a concrete cover of 40mm and stirrups of 10mm with fc' of 35Mpa and fy of 276Mpa. The reinforcement used has a diameter of 16mm. Calculate the following. 14. Calculate the maximum moment

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Design beams. Where fc' = 35 Mpa, fy = 420 Mpa. and bar 25 mm. L.L=10 KN |im+ L.L-25 kN L.L=15 kN -2…

A: Solution: Factored load: 1.2 DL+1.6 LL=1.20+1.610=16 kN=1.20+1.625=40 kN=1.20+1.615=24 kN Find the…

Q: 32 A beam which is composed of concrete and a wide flange steel is subjected to moment M = 1126…

A: Given: A composite beam made up of steel and concrete having Compressive stresses to be carried by…

Q: d Craked Section 1. A doubly reinforced beam ha

Q: A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the…

Q: A Simply supported beam has a width of go0 effective depth of g90 mm - It is rein forced at the…

A: Solution:- Distance of neutral axis from top: xu=0.87fy×As0.36fc×b=0.87×415×24640.36×34×300…

Q: Design a one-way slab for inside of a RC Building. NWC. Use slab thickness = 6/1/2" Additional WDL =…

A: One-way slab : Because of its geometry, a one-way slab is a slab that is supported by parallel walls…

Q: the final answer should be fc= 10.07 MPa and fs = 155.9 MPa

A: In this problem we calculate flexural stress in concrete and steel using equalent area method. In…

Q: Determine the dead load and the live load uniform loads of the beam cross-section shown in addition…

A: Given data l= 8 m Hinge support = 1.25 m (from left) roller support = 1.5 m from right end fc' = 21…

Q: Q2: The reinforced concrete Isolated T-Beam shown in Figure 2, carried uniform distribution live…

A: Given Live load=35kN/m Dead load=30kN/m Fc=28Mpa Fy=420Mpa

Q: Problem 1: The one way-slab spans 4.0 m. In addition to its own weight, the slab supports a…

A: Design as per IS 456 Limit state depth

Q: "Q1.19-.A rectangular beam has dimensions of 270 mm by 640 mm with an effective depth of 571 mm and…

A: Answer We are given Width b = 270 mm Overall depth h =640 mm Effective depth d = 571 mm Steel = 4…

Q: A rectangular concrete beam has a width of 300mm and an effective depth of 550mm. The beam is simply…

A: Given Data:Width = 300mmeffective depth=550mmspan=6mDead load = 35kN/mLive load =…

Q: The geometry and reinforcement configuration of the column is given below. The material properties…

A: fy=420 MPafc'=30 MPab=400 mmh=600 mmDesign axial load=1250 kNDesign moment=550 kN

Q: 2) As shown is the partial plan of the corridor of a certain building. If live load is 4 KPa and…

Q: A simply supported one way reinforced concrete floor slab has a span of 3 m. It carries a service…

Q: a rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

A: Given : Width = 250 mm Depth = 500 mm is reinforced at the bottom with 4-20-mm-diameter bars and…

Q: M1BQ25. A rectangular beam has a width of 390 mm and an effective depth to the centroid of the…

A: fy = 415.9MPa fc = 35.8MPa B(width) = 390mm d (depth) = 522.5mm dc (cover at compression side) =…

Q: Q1/The area of the reinforcement for a rectangular reinforced beam is 1991mm². The width of the…

Q: Determine M for a reinforce concrete beam 16 in. wide by 32 in. deep reinforced with seven No. 10…

Q: a) Design a cantilever beam with a span length of 2.6m. The beam is exposed to 34kN/m dead load and…

A: Solution: Hi! Thank you for the question As per the honor code, We’ll answer the first question…

Q: A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the…

A: In a singly reinforced beam, the longitudinal reinforcement is restricted to the tension…

Q: For a reinforced concrete beam, the cross-sectional dimensions are bxh=300 mmx600 mm, a, 35 mm. The…

Q: Seatwork No. 1 1 whole yellow sheet of paper or bond paper A rectangular beam having a 7-m simple…

A: Given:- The span length of the beam = 7 m The superimposed dead load = 28 kN/m The live load = X =…

Q: "Q1.11-A rectangular beam has dimensions of 300 mm by 730 mm with an effective depth of 676 mm and…

A: Given Data: The dimension of a rectangular beam is 300 mm×730 mm. The effective depth of the beam is…

Q: Q.06. A T beam is to be used as a bridge over a small roadway. Concrete dimensions are b= 48- in.,…

A: A T beam which is used a bridge over a small roadway is given .The dimension's of beam and all…

Q: Problem: Design the reinforcement of a rectangular beam to carry a factored moment of 272 kN.m. The…

A: Mu = 272 kNm or 272 x 106 Nmmb = 250 mmd = 400 mm f'c = 20.7 MPafy = 345 MPa

Q: 9.4- A concrete slab with 180 mm thickness support dead load 5kN/m? include self- weight and service…

A: We have to determine adequacy of slab thickness and steel area required at point 1, 2, 3&4 and…

Q: Refer to the figure. bw

A: (a) using 28mm diameter main reinforcement bars, determine the nominal ultimate moment capacity…

Q: Q-A rectangular 230 mm x 350 mm (effective depth) beam is given. The factored shear force acting at…

A: Given- Rectangular beam 230 mm×350 mm, Factored shear force- Fsf=80 kN, Permissible shear stress…

Q: t028/ina reinforced con crete beam, b= 500 mm, d=750mot o dp= 6000 mm? ,and n=10. What ave the…

Q: A continuous concrete flooring system consists of a 3-in thick concrete slab supported by 15-in wide…

Q: 1025// In a reinforced concrete beam, b= 250mm, d = 450mm and n = 1o. The actual mavimine stresses…

Q: A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the…

A: When an element is subjected to a bending moment, the effective depth is the distance between the…

Q: 3) Calculate the nominal moment strength and the design ultimate moment of the precast T-beam shown…

A: Given: Span, L = 30 ft fc = 4 ksi fy = 60 ksi b = 40 in bw = 10 in d = 20-2=18 in rebars, 4-#9 bars…

Q: Question A concrete beam of rectangular cross-section of 200 mm x 400 mm is pre-stressed with a…

A: GivenCross-section-It is needed to find the maximum compressive stress in the concrete.

Q: For a section 6 inches wide and 14 inches deep, and a cover of 2 inches, what is the maximum safe…

A: The moment carrying capacity of the balanced beam section is M = CZ where C - Compressive force Z…

Q: SHOW CLEAR SOLUTIONS (STEP BY STEP). USE NSCP 2015. uaume a concrete cover of 40mm, 10mm stirrups…

Q: III. A simply-supported rectangular concrete beam with a width of 300mm wide, 600 mm total depth,…

A: GIven : Doubly reinforced beam with 6m length n= 8, 300mm X 600 mm cross section fc = 28 MPa &…

Q: Determine the maximum live load that the beam can carry if the beam depth is 600mm and beam width is…

Q: reinforced concrete symmetrical triangular shape beam has an effective depth of 600mm. The width of…

A: Given:- The effective depth of the triangular beam = 600 mm The width of the base at depth of 600 mm…

Q: 1.2m 10 cm 7cm -7cm This concrete beam has four A-35 steel rods of one centimeter diameter and a…

A: Stresses in Concrete Beam : A concrete beam is a load bearing unit which is used to carry both…

Q: Situation. A simply supported one way RC slab has a 3 m span. It carries a serv

Q: plz, solve all the parts of this problem. Plz, use ACI Code. Reinforced Concrete Design-1…

A: Solution: Given: Span = 24 ft b = 15 in d = 24 in DL = 1 K/ft LL = 1.4 k/ft fc = 3 ksi fy = 40 ksi

Q: 7 1 التاريخ 2 الموضوع Q₁: The 300 mm X 300mm concrete columu. (EC 25 GPa and ac = 5.5 X 106 / "℃) is…

A: Given Data Size of column = 300mm × 300mm Diameter of reinforcement (d) = 18 mm × 4 no. Modulus of…

Q: (PROBLEM 2) A three-member frame ABCD is loaded with ultimate gravity and lateral loads as shown in…

A: The axis that passes through the cross-section of the beam or a shaft that represents the zero…

Concept explainers

Steel Framing

A steel frame consists of a skeleton frame structure comprising of horizontal I-beams and vertical steel columns fitted in a rectangular grid building construction to brace the floors, walls, and the roof of the building held onto the frame. Due to the implementation of this methodology, the construction of the skyscrapers was feasible.

Question

Problem No.2A 250x400mm beam with a concrete cover of 40mm and stirrups of
10mm with fc' of 35Mpa and fy of 276Mpa. The reinforcement used has a diameter of
16mm. Calculate the following.
14. Calculate the maximum moment
20 KN/m
5 KNim
10 kN
65 kN
z (m)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Shear Force Diagram

VIEW

Step 3 Maximum Bending moment

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

"Q1.16-.A rectangular beam has dimensions of 270 mm by 670 mm with an effective depth of 620 mm and is reinforced with 5- 20 mm ø. Concrete cover is 50 mm. The concrete cylinder strength f'c = 30.7 MPa and the tensile strength in bending is the modulus of rupture. The yield point of the steel is 449.5 MPa. The beam carries a bending moment of 67 kN-m. Use transformed section method to answer the following: (1) Compute the concrete compression stress at the top, (2) Compute the concrete tension stress at the bottom, (3) Compute the stress in the steel. (4) Assess the adequacy of the beam design." Use the editor to format your answer width, b ... effective depth, d total depth, h
A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of tension steel bars. Tension reinforcement consists of 6 – 28mm dia in two rows, compression reinforcement consists of 2–22mm dia, fc’ = 27.6MPa, fy = 414.7MPa, d’ = 60mm, L = 4m, the Unit weight of concrete is 24.56kN/cu.m 1.) The depth of the concrete stress block is ____ mm.
Calculate Mn
SITUATION A: The floor system shown has the following applied loads. Super Imposed Dead Load = 2.00 kPa Live Load = 1.90 kPa Slab Thickness = 100.00 mm Weight of Concrete = 24 kN/m3 Self-Weight of the beam = 1.92 kN/m Material Specifications: f’c = 21.00 MPa fy = 345.00 MPa Steel Cover = 50.00 mm What is the maximum positive moment of beam BE, acting on the midspan? in kN-m What is the maximum steel ratio of the section located at the supports? What is the actual steel ratio of the beam section at the supports? What is the ultimate moment capacity of the beam at the supports? in kN-m What is the effective flange width at the midspan? in mm What is the height of the compression block of the section at midspan? in mm What is the ultimate moment capacity of the beam at the midspan? in kN-m What would be the height of the CHB that can be placed on beam BE? Assuming the weight of the blocks is 2.30 kN/m per meter height? in meters
I need the answer to the question in reinforced concrete
Principle of Reinforced Concrete Design
The following is a cross-section of a tied column reinforced with 16-32 mmø. Using fc' = 28 MPa and fy = 415 MPa. Size of aggregates used is 25 mm. O Computè the safe ultimate load that the column could carry. ® Compute the spacing of the 10 mm wires. 3 . Compute the min. clear cover over the tie wire. O Compute the clear spacing between longitudinal bars. -600 600
A reinforced concrete beam that is 375 mm wide and 500mm deep must resist a service live load moment of 250 kN-m and a service dead load moment of 150 kN-m. Use f'c-21 MPa and fy=415 MPa. The effective concrete cover is 65mm (to the centroid of reinforcements). 1. Determine the area of compression steel reinforcement (If required. Answer O if not) in mm² 2. Determine the minimum number of 25 mm diameter bars to be provided to satisfy the demand ultimate moment 3. Determine the maximum number of 25 mm diameter bars to be provided to have a tension controlled section Answer 1: 2403.21 correct answer: Answer 2: 9.00 Answer 3: 8.00
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of 18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis.
A floor slab 100 mm thick is cast monolithically with beams 250 mm wide 450 mm deep spaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports a service live load of 2.1 kPa. Using f.-21 MPa, rebar strength f, 415 MPa, calculate the following if a typical interior beam is reinforced with 3- 16-mm-dia. flexure bars at the bottom enclosed with 10-mm-dia. stirrups: 1. Nominal moment capacity (kN-m) of a typical interior beam in positive bending considering T-beam geometry. A. 96.66 C. 91.10 Maximum factored uniformly distributed load (kN/m) a typical interior B. 86.99 D. 81.99 2. beam can sustain against positive bending. В. 27.83 с. 26.23 D. 29.15 A. 30.93 3. Maximum service superimposed dead load in kPa. A. 17.73 C. 16.52 B. 11.08 D. 14.77
Show all solutions