PROBLEM: Knowing that the tension in cable AC is 1500 N, determine a, the position vector along line AB b. the components of the force exerted on the plate at C. 360 mm- 920 mm 500 mm D 800 mm

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: Problem: Determine F to keep the block at rest. 500 kN IS 30

A: Given: A block of weight 500 kN is resting on a inclined plane, which makes an angle of 300 with…

Q: solve and show every step with right answer

A: Data given - Rectangular cross section 225×75 mm2 Torsional moment = 20kN Axial Compressive force =…

Q: Show your complete solution including the diagrams and box your final answers with their appropriate…

A:

Q: The cylindrical gasoline tank on a tractor is 11 inches in diameter and 36 inches long. How many…

A:

Q: Draw the following figure: 50000- 8.0000

A: The drawing of the given figure will be:

Q: Given the isometric drawing, draw the multiview projection. The multiview projection of the glass…

A: Draw the isometric view.

Q: In Part a, could you please explain where the 4 comes from on the line before the answer.

A:

Q: INSTRUCTIONS: Solve for all unknowns (magnitude and direction). A 10' 300# 10' 150# B 5'

A: According to the given data A beam  AB is given  We need to find Reaction  at point A and B

Q: solve by showing every step.

A: Given data: The ultimate tensile strength of component is Sut = 30 ksi. The ultimate compression…

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: QUESTION 8 What is the specific volume of air at 184 K and 139.23 kPa? Give your answer in mkg to 3…

A: Solution is attached below:

Q: 2. From the given figure below, solve for the bar Y from the reference line. (choose the nearest…

A:

Q: Completely solve and illustrate the problem. Show what are given, required, illustration, analysis…

A: given; diameter of solid shaft(ds)=4.2in                                       =0.1068mweight of…

Q: Develop two possible hierarchies for assembling a model from the parts given below: Top Pins…

A: Given question: Develop two possible hierarchies for assembling a model from the parts given below:…

Q: A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center.  1- Two…

A: Given Data, W = Weight of the seesaw = 45 lb L = Length of the seesaw = 5 m Condition 1 :-…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: PART VI. Given that f(x,y) = (x +y)/2k, where x=-1,1,2 and y= 0,2,4 1. Find k 2. Find the marginal…

A:

Q: Please use different values. This answer you already gave me for a similar question. These values I…

A:

Q: Solve for the mobility. Show your logical and accurate solutions after every fig

A:

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: In a hot water heating

A:

Q: Find the value of P

A: Need to find Values of P

Q: Read the questions again. Your answer is not what I'm asking. Please redo it.  where is my FBD. Can…

A: The free-body diagram of the smaller cart is shown below.The free-body diagram of the larger cart is…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: The Answer is cut off on the right side.

A:

Q: axis of the solid. Draw its projections, sectional front view & true shape of the section. Also…

A:

Q: An 4 cylinder engine has a crankshaft sp of 3,500 rpm, a bore of 3.8 inches, a str of 3.8 inches,…

A: Givenk=4N=3500 rpmd=3.8in =3.8×0.0254=0.09652mL=3.8in=3.8×0.0254=0.09652mP=210…

Q: 1- Sketch front, right and top views of the following object. Each grid represents 10 mm. Front

A: Given: Sketch Front, top and right side view of the given isometric view.

Q: olve show full solution

A: To find:The principle stress at point A and absolute maximum normal stress at and absolute maximum…

Q: I need parts 3 and 4 answered pertaining to the print provided.  I asked this question previously on…

A: (3) In the empty space of revision A9 a general note 3.6 is added stated that the revised geometric…

Q: Please show all the steps, thanks

A:

Q: Complete the each drawing by adding the missing details in 5 and 6 both questions.

A:

Q: Give a steps by steps answer of the solution

A:

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Q: friction t

A: FIg:FBD Fr=μN∑Fy=0N=mgcosθ∑Fx=0μN=mgsinθμmgcosθ=mgsinθμ=tanθ

Q: can the solve the last three quetsions please

A: mass of refrigerant R-22, m= 2kgThe initial pressure, P1= 6.8 barThe initial state is saturated…

Q: sketch a rube goldberg machine using the following operations dominoes falling, rolling ball, pulley…

A: A rube goldberg machine is to be drawn considering the operations such as falling, rolling ball,…

Q: Write legibly and box the final answer

A:

Q: d) Determine the obtuse angle between F1 and F2 using the dot product. Provide Find, Problem…

A:

Q: Please answer part c and e onwards with working out and answer and please label the parts as you…

A: c) TDC=Top Dead Center BDC=Bottom Dead Center Stages Ideal cycle Actual cycle Stage 1 It is…

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.