Problem I. With the ongoing extension of Manila Skyway, a series of 250 mm diameter circular poles are to be used as vertical member each carrying a compressive load of P= 7.1 kN acting 150 mm from centroidal axis of cross section and a lateral load of 0.45 kN at the top. If the height and the unit weight of the pole is 3 m and 22 kN/m³, respectively. a. Determine the maximum compressive stress at the base of the pole. b. Determine the maximum tensile stress at the base of the pole. c. Calculate the maximum shear stress at the base of the pole.

Problem I. With the ongoing extension of Manila Skyway, a series of 250 mm diameter circular poles are to be used as vertical member each carrying a compressive load of P= 7.1 kN acting 150 mm from centroidal axis of cross section and a lateral load of 0.45 kN at the top. If the height and the unit weight of the pole is 3 m and 22 kN/m³, respectively. a. Determine the maximum compressive stress at the base of the pole. b. Determine the maximum tensile stress at the base of the pole. c. Calculate the maximum shear stress at the base of the pole.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum average shear stress developed in 30mm diamter pin
QA rectangular Pier of 2.5 mx 2.0m is subjected to a compressive load of 650 kn as shown in figure below. Find the stresses on all four Corner of the Pier. 2M A B) 0.3m 2.5m Point Load 0.5m
BRAIN EXERCISE PROBLEM 1 Determine the maximum shear stress and the maximum flexural stress of the beam. The cross-section of the beam is 150 mm x 350 mm. A B 10 KN 15 KN/m C 1.50 1.00 1.50 10 KN/m D D.Lopez 2.00 in meters Figure A: Overhanging Beam E
Please show complete solution.
eiches : Two-way slab system (6.1*6.1 m) as shown in Fig. 1, subjected to a live load of 2 kN/m² and superimposed dead load of 3.5 kN/m². Design the panel $2 for max positive and negative moments. The column dimension 300* 300 mm and the supporting beams are 300 mm width. Use fe=21 MPa and fy = 420 MPa arks). Fig.1 S2 6.1m 6.1m
Solve it
A 4.75-in. outside diameter polyethylenepipe designed to carry chemical waste is placedin a trench and bent around a quarter-circular 908bend (see figure). The bent section of the pipe is52 ft long.(a) Determine the maximum compressive strainεmax in the pipe.(b) If the normal strain cannot exceed 6.1x10 -3 ,what is the maximum diameter of the pipe?(c) If d = 4.75 in., what is the minimum acceptablelength of the bent section of the pipe?
Question
An eight-story commercial building is proposed to be constructed in Cavite. The structure shall be a reinforced concrete building (no shear walls). The weight per floor is estimated to be 1800 kN. The roof deck weighs 1700 kN. Solve for the base shear, lateral forces per floor, and check for story drift. Height per floor is 3.5m Depth of the foundation to the ground level is 1.8m Column stiffness is 300 kN/ mm per floor. Based on the National Structural Code of the Philippines
The prestress T-beam section has a simple span of 6 m. The tendons is subjected to initial stress of 900 MPa with an area of 800 mm. Assuming a loss of stress of 18%. no tension will be acting at the bottom and maximum stress of 9.5 MPa at the top should not exceed. a) Determine the stress at the bottom due to the final prestressing force alone. b) Determine the safe moment that the beam could carry based on the allowable stresses. (kN- m) c) Determine the sate uniform live load that the beam could carry if the unit weight of concrete 24 kN/m°. (N/m) d) Determine the stress at the top due to the final prestressing force alone. (MPa)
A roadway sign weighs 7.4 kN and is supported by a structural pipe that has an outside diameter of 160 mm and a wall thickness of 11.5 mm. The resultant force of the wind pressure acting on the sign is 13 kN, as shown. Assume a = 8.7 m, b = 4.1 m, P₂ = 13 kN, and Py = 7.4 kN. (a) Determine the normal and shear stresses OH, Txy at point H. (b) Determine the normal and shear stresses OK, Tyzk at point K. Answers: OH = TxyH = OK = Tyzk = y HK i i i P₂ i b a MPa. MPa. MPa. MPa.