Please Full solution with all the steps. BIG and clear Handwriting. Thank you Problem B-8–4Find the transfer function X(s)/X;(s) of the mechanical system shown in Figure 8-24.Obtain the displacement x,(1) when the input x;(1) is a step displacement of magnitudeX, occurring at i = 0. Assume that x,(0-) = 0. The displacement x„(t) is measuredfrom the equilibrium position before the input x;(!) is given.k1Figure 8-24 Mechanical system.

Problem B-8-4 Find the transfer function X(s)X;(s) of the mechanical system shown in Figure 8-24. Obtain the displacement x,(t) when the input .r,(1) is a step displacement of magnitude X, occurring at 1 = 0. Assume that x(0-) = 0. The displacement .x(t) is measured from the equilibrium position before the input x,(1) is given. k1 k2 Figure 8-24 Mechanical system.

Problem B-8-4 Find the transfer function X(s)X;(s) of the mechanical system shown in Figure 8-24. Obtain the displacement x,(t) when the input .r,(1) is a step displacement of magnitude X, occurring at 1 = 0. Assume that x(0-) = 0. The displacement .x(t) is measured from the equilibrium position before the input x,(1) is given. k1 k2 Figure 8-24 Mechanical system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Specific Instructions: Solve each problem NEATLY and SYSTEMATICALLY. Show your COMPLETE solutions and BOx your final answer. Express your answers in 2 decimal places. TOPIC: ENGINEERING ECONOMICS Problem: A company invest Php 100,000 today to be repaid in 5 years in one lump sum at 12 % compounded annually. If the rate of inflation is 3 % compounded annually, approximately how much profit, in present day pesos, is realized over the five years?
sketch the development
please provide a clear solution and FBD. please answer within 30 minutes, thank you!
Hello sir, I want to solve in a clear beautiful font that will be a manual line with a pen I know a strange request and don't forget my name and thank you sir, God bless you
|Read the problem statement and the solution provided. There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. You can make the corrections directly on a copy of this provided solution, but make sure you clearly explain the corrections. Problem: Consider fully-developed flow of water through a 24-cm diameter tube. The water comes in at 20°C and exits at 40°C. The surface temperature of the tube is uniform at 60°C. The water flow has a mass flow rate of 0.24 kg/s. What is the average convection coefficient of the water flow? Solution: We have T, = 60°C, Tmi = 20°C, Tmo = 40°C, So, the bulk-mean temperature is Tm = 30°C. The appropriate properties are: u = 7.98 × 10-4 kg/ms; k = 0.615…
i need clear ans and solve very very fast in 20 min and thank you | DYBALA A part under forming force showed that 15% decrease in thickness and 10% increase in width, find the change in length (sign and value) if initial length is 200 mm?
solve 30-40 minutes hand written asap..i'll give you multiple upvote
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Summary/Conclusion Discuss the strengths of your design and how it met the specifications. Discuss your assumptions and why they are valid. Discuss what you might change about your design in a redesign effort. Format: The project should be presented as a design report using a word processor. Include any hand calculations in an appendix. More details will be provided. Choose to design either a slip-jaw or channel-lock pliers to last for 25 years of use by a professional. Use an appropriate tool steel for the pliers. Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not given. Slip Jaw Pliers A= 9.00 inches B=1.00 inches C= ? D=1.25 inches H= 1.875 Inches D B A
In the last few steps, where did 0.4 come from?
Can someone please help to solve this question following the directions and showing neat work and formulas and drawing all needed diagrams. PLEASE AND THANK YOU!!!
Can you please do the same problem but show the work better its hard to follow steps