problem: A Laser doppler velocimeter was used to determine the velocity of the water flow in an open channel whose cross section is a triangle with a base of 0.532 m and a depth of 0.444 m. If the velocity of the water flow is 8.97 m/s, determine

Q: To develop an introduction and an objective for a report of a fluid pumping project, which aims to…

A: The field of mechanical engineering encompasses a wide range of applications, one of which is the…

Q: . Water is flowing through a pipe, driven by only gravity (no pumping). a. If water is flowing…

A:

Q: 7. Water from the reservoir is pumped over hill through a 90 cm diameter pipe, and the pressure of…

A: Solution: Given Data: *The diameter of the pipe is, D=90 cm *The pressure at the summit is, P=200…

Q: Given the conditions on a converging-diverging wind tunnel. At the reservoir pressure is measured to…

A:

Q: 10. Water flows from a lake as shown below at a rate of 5.0 ft³/s. Is the device inside the building…

A:

Q: A crude oil is to be pumped out through a pipeline at flow velocity, v of 5 m/s. As a process…

A: Spring diaphragm is a simple mechanism.

Q: Find out the expression for the specific speed of a water turbine in terms of H.P. developed, the…

A: Write the expression for the specific speed of a water turbine in terms of H P developed, the speed…

Q: Determine the discharge at pipeline 3 in lit/sec assuming f=0.02 for all pipes.

A: Given data Discharge (Q)=0.86m^3/s  Friction factor (f) =0.02

Q: Situation: Water is pumped from one tank to another. Find: r/d = 1, D = 10 in, L = 50 ft. f2 =…

A: Since the pipe has constant area of cross section through out.…

Q: A certain centrifugal pump was tested and its performance curves can be approximated as follows: H =…

A:

Q: For oil flow through a pipe, velocity increases O 1, with decrease in area of cross section O 2.…

A: Option : With decrease in area of cross section

Q: 54. Derive the time to drain the tank of Example III6.6.2 from the observation that t = V,/VA,.…

A: Given: Volume of the tank→Vt=hi×At………equation1 where→hi=initial height of the tank   and→At=cross…

Q: pumped fluid distribution system is being designed to deliver Q=200 gal/min  of water to a cooling…

A: Vvhh

Q: Illustration 10.7 A covered, baffled vessel, 0.5 m (19.7 in) diameter, 0.5 m deep is to be used for…

A:

Q: Water is to be supplied to the inhabitants of a college hostel through a supply main. The following…

A: We have provided data from the question are,  L=4000 m  N=Number of inhabitants=3000  Q=180…

Q: Estimate the power available from a proposed micro hydro scheme at a site having a small stream of…

A: Given: Volumeteric flow rate of water (Q)=100l/sHead (H)=30mOverall efficiency of the system…

Q: A turbine is located at an elevation 200 m. below the surface of the water intake. The friction loss…

A:

Q: Problem 1. Gas flows through a pipe whose diameter gradually decreases from 300 mm at section A to…

A: The given data in the problem is represented in the following attached image:

Q: 2.1. A water hammer is a phenomenon caused by the sudden increase or decrease in fluid velocity…

A: To choose: 2.1: To select which option is correct for gradual valve closure time. 2.2: To select…

Q: QUESTION 2 A pipeline of 50 mm diameter and 4.5 km length connects two reservoirs whose constant…

A: by problem,QB=QCQA=QB+QCQB=QC=QA/2f=0.0075DA=DB=50mmDC=?For A & B reservoir,ZA-ZB=fCADA X VA22g…

Q: Determine the pump head (unit: meter or kPa), using the following parameters

A:

Q: 2 A horizontal garden hose 15 m long with an interior diameter of 1.25 cm is used to deliver water…

A: Given:L=15 md=1.25 cm =0.0125 mQ=40 cm3/s =40*10-6 m3/sT=20°C

Q: An ogee spillway has a design flow rate of 14,100 cfs (ft/sec). An energy dissipater is being…

A: Given data: Design flow rate of the ogee spillway, Qprototype = 14,100 cfs (ft³/sec) Initial depth…

Q: llustration 10.7 A covered, baffled vessel, 0.5 m (19.7 in) diameter, 0.5 m deep is to be used for…

A:

Q: Example 7.4: In a flow system, two a centrifugal pumps were connected in series. Use tabulated data…

A: Given: Find:The operating point for;a Only pump 1 is runningb Only pump 2 is runningc Both pumps…

Q: Develop an introduction to a fluid pumping project, which aims to experimentally find the…

A: Step 1: Understand the project scope by finding the characteristic curves of the pump for your…

Q: 1.1 Define centrifugal pumps and briefly discuss their operating mechanisms. 1.2 Write the reasons…

A: 1. Centrifugal pump is a mechanical device which is designed to move a fluid by transfer of…

Q: 1) The equation for finding the water head in an open channel flow is given below. is given. In this…

A: Given: The width of channel, B = 8 unit The flow rate, Q = 5 unit The height, H = 0 to 2 unit

Q: A Pelton wheel is supplied with 6kg/s of water at 70m/s. The buckets rotate on a mean diameter of…

A: Given , Pelton wheel  mass flow rate =  6kg/s velocity v1 =  70m/s. deflection angle = 165º mean…

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A:

Q: 6.88 A water jet strikes a cart as shown. After striking the cart, the water is deflected vertically…

A: To find :  The time required for the cart to achieve a speed one half of the jet speed. Given :  The…

Q: In the pumping system shown below, determine the following. a. Head loss at suction in m b. Head…

A:

Q: 8.59 Two tanks A and B, of constant cross-sectiona! area of 10 m² and 2.5 m², respectively, are…

A:

Q: The diameter of the pipe is 100 mm and velocity of oil (SG=0.89) is found to be 3,4 m/s. 32.…

A:

Q: Incompressible fluid flows with a velocity of 10 m/sec through a pipe of diameter of 1.5 m and…

A: Given  V1 = 10 m/s D1 = 1.5 m A1 = 1.767 m2 annular gap (t) = 0.1 m      To determine  velocity (V2)…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.