Problem (A) Find the thickness of metalnecessary for a cylindrical shell of internaldiameter 160 mm to withstand an internalpressure of 8 N/mm². The maximum hoopstress i the section is not to exceed 35N/mm²probaken (b).Determine the maximum andminimum hoop stress across the section ofa pipe of 400 mm internal diameter and100 mm thick, when the pipe contains afluid at a pressure of 8 N/mm². Also sketchthe radial pressure distribution and hoopstress distribution across the section

“Since you have posted multiple questions, we will provide the solution only to the first question…

Problem (A) Find the thickness of metal necessary for a cylindrical shell of internal diameter 160 mm to withstand an internal pressure of 8 N/mm². The maximum hoop stress i the section is not to exceed 35 N/mm²

Problem (A) Find the thickness of metal necessary for a cylindrical shell of internal diameter 160 mm to withstand an internal pressure of 8 N/mm². The maximum hoop stress i the section is not to exceed 35 N/mm²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bronze bar 3 m long with a cross-sectional area of 350 mm2 is placed between two rigid walls. At a temperature of -20°C, there is a gap A = 2.2 mm, as shown in the figure. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use a = 18.0x 10-6 / °C and E = 80 GPa. 3 m-
A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid A36 steel with a 20 mm diameter (E = 200 GPa). Outer sections DA and BC are solid red brass (E = 101 GPa) with a 50 mm diameter. A previous analysis by a now departed coworker correctly determined that the internal normal stress in DA was 54.952 MPa compression. You are asked to determine the horizontal displacements of joints A and B.
Determine the tensile strain Original length L = 500 mm Tensile deformation = 2.5 mm
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 13 mm and an elastic modulus of E = 70 GPa. The steel rod has a diameter of 20 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.9 m, and c = 1.2 m. What is the magnitude of load P that is necessary to displace point A 14 mm to the left? a b (1) P Answer: P = i (3) B KN O
A steel tube is rigidly attached between an Al rod and a bronze rod. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress of 80MPa in Al, 150MPa in steel and 100 Mpa in bronze. -1.0m 200 mm² 2.0m Steel 400 mm² 2P -2.5 m Bronze 500 mm²
4. A titanium alloy (Ti-6Al-4V) pipe has a bronze C86100 copper alloy core and is subjected to a force, P = 150 kN. Determine the average normal stress in each material and the elongation if the pipe has an outer diameter of 90 mm and an inner diameter of 70 mm. (Solution: On = 25.789 MPa, 22.135 MPa, 8 = 0.086 mm) 400 mm-
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 210 mm, a wall thickness of 11 mm, and a length of 5.8 m. The pipe supports a compressive load of 675 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) d = i mm AD= i mm
4 A metal wire Im long and of 10mm diam eter is stretched by a load of 50 kg. If E = 7 x 10³ N/mm² for the metal, find the (a) stress (b) strain and (3) Poisson's ratio if the lateral strain is 2.6x 105 m/m.
2.)
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises after a load W = 120 kN is applied. Steel rod Bronze rod A (mm²) 350 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83 O Steel 1.5 m 1.0 m- 2.5 m 9. Determine the stress at the steel rod in MPa when there is a temperature rise of AT = 36 °C. W Bronze 3 m 1.5 m-
PLEASE ANSWER ASAP TY! a) Determine the cross-sectional area of the structural tube (in mm2) b) Determine moment of inertia of the cross-section about the neutral axis (in mm4) c) What is the maximum normal stress at point K (in MPa)? Include negative sign if compressive. d) What is the axial stress at section H-K (in MPa)? Include negative sign if compressive. e) What is the flexural stress at section H-K (in MPa)? f) What is the maximum normal stress at point H (in MPa)? Include negative sign if compressive.
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 170 mm, a wall thickness of 12 mm, and a length of 4.5 m. The pipe supports a compressive load of 630 kN. After the temperature of the pipe drops 53°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) d = i AD= i mm mm