Problem 8: Calculate the apparent power, power factor, real power and reactive power associated with a load if it draws complex power S equal to 1+ j0.5 kVA а. b. 400 VA с. 1502-21° VA d. 75225° VA

Problem 8: Calculate the apparent power, power factor, real power and reactive power associated with a load if it draws complex power S equal to 1+ j0.5 kVA а. b. 400 VA с. 1502-21° VA d. 75225° VA

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.11P

See similar textbooks

Similar questions

Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
S. 20020°V L rms S. In the circuit in the figure; • L1 load draws 15 kVA with lagging power factor 0.6. • The load L 2 draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the reactive power for the load L, ? O 9000 O -3600 O 2700 O 12000 O 4800 O 4500
A synchronous generator may be represented by a voltage source of magnitude 1.7 p.u. in series with an impedance of 2 p.u. It is connected to a zero-impedance voltage source of 1 p.u. The ratio of X/R of the impedance is 10. Calculate the power generated and the power delivered to the voltage source if the angle between the voltage sources is 30°.
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
Two three-phase alternators operate in parallel and the excitation is such that theinduced emfs are 1 kV/ph. The load admittance is (0,427 – j0,214) S. Theadmittance/phase of the machines are (0,0262 – j0,499) S and (0,0218 – j0,312) Srespectively. The emf of B leads A by 10°e. Calculate:(a) the terminal voltage(b) the current supplied by A(c) the power factor of B
A 250 - kVA, 0.5 lagging power factor load is connected in parallel to a 180 - W, 0.8 leading power factor load and to a 300 - VA, 100 VAR inductive load. Determine the total apparent power in kVA. Express your answer in polar form.
Which of the following descriptions IS NOT correct for loads in power systems? A. The purely resistive load absorbs the real power from the power grid B. The purely inductive load absorbs the positive reactive power from the power grid C. The purely capacitive load absorbs the positive reactive power from the power grid. D. The average value of the instantaneous power through loads is equal to its real power. In an ac circuit, power factor correction or improvement is achieved by A. Connecting a resistor in parallel with the inductive load B. Connecting an inductor in parallel with the inductive load C. Connecting a capacitor in parallel with the inductive load A balanced delta-load can be converted to an cquivalent balanced wye- load by dividing the delta-load impedance by A. square root of 3 В.3 C. 1/3
a load of 15 mva with power factor 0.86 lagging is given. Calculate the reactive power delivered by shunt capacitors to increase power factor to 0.9 lagging
If the load is connected to the generator thgrough an inductive line and the voltage at the load side is the same as the voltage at the terminals of the generator, which of the following must be true? O A. The reactive power is flowing from the generator to the load and from load to the generator at the same time. O B. The load is disconnected, and no power is delivered to the load. O C. The load has a poor power factor and it's absorbing too much reactive power. O D. None of the other choices are correct O E. The generator is unable to produce reactive power; therefore, the reactive power is flowing from the load to the generator.