Problem 7Knowing that E = 29x106 psi, and v=0.30, determine the internal force in a bolt if the diameter is observedto decrease by 0.5x10¹³ in and the initial diameter is 2.5 in.

For any doubt let me know in comment section i will clear your doubts

Answered: Problem 7 Knowing that E = 29x106 psi,…

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter15: Thermodynamics

Section: Chapter Questions

Problem 13PE: A hand—driven tire pump has a piston with a 2.50cm diameter and a maximum stroke of 30.0 cm. (a) How...

See similar textbooks

Similar questions

A fluid at a pressure of 3 bar and with a specific volume of 0.18 m°/kg contained in a cylinder behind a piston expands reversibly to a pressure of 0.6 bar according to the law p =2 v² where C is a constant. Calculate the work done by the fluid on the piston.
M6
b) Each cylinder in a four-cylinder car engine has a bore diameter of 55.20 mm and the stroke for each piston is 127.50 mm. Calculate the cubic capacity of the engine in in cubic centimetres (cm³) and give your answer to two decimal places. c) For the engine mentioned in (b), the compression ratio, r, is 4.45 for the engine in, calculate the clearance volume per cylinder in in cubic centimetres (cm³) and give your answer to two decimal places.
I have a linear piston and it will be filled with wax (g) its expansion will cause an output force, however, it is not known how much wax is needed for it to expand inside and thus cause a force and also we don't know how small can the internal cylinder containing the wax be. Since the goal is to be able to have a suitable dimension enough to make the wax expand inside and cause a force of 200 lbs. I want to know how to calculate how much wax is needed to give the required output force of 200 lbs and what dimensions can the internal cylinder have.
Verify the equation of psi and v
The plunger of a syringe has an internal diameter of 1.0 cm and the end of the needle has an internal diameter of 0.30 mm. A practitioner squeezes across the plunger very lightly, but no serum is emitted by the needle into a vein. So the practitioner gradually increases the force that she exerts across the plunger and eventually serum begins to be emitted from the needle into the vein. Assuming no friction, what is the minimum net force that the practitioner applies across the plunger in order that serum begins to be emitted from the needle into the vein? Take the pressure of blood in the vein to be 20 mmHg above that of atmospheric pressure. 3.3 N 1.2N 0.21N 0.70 N 1.4 N O 23 N
c) Answer the question shown in the image
A hand-driven tire pump has a piston with a 2.50-cm diameter and a maximum stroke of 30.0 cm. (a) How much work do you do in one stroke if the average gauge pressure is 2.40 × 105 N/m2 (about 35 psi)? (b) What average force do you exert on the piston, neglecting friction and gravitational force?
The plunger of a syringe has an internal diameter of 1.0 cm and the end of the needle has an internal diameter of 0.35 mm. A practitioner lightly squeezes the plunger, but no serum is emitted by the needle into a vein. So the practitioner gradually increases the squeezing force that she exerts on the plunger such that serum begins to be emitted from the needle into the vein. Assuming no surface tension or friction, what is the minimum squeezing force that the practitioner applies to the plunger in order that serum begins to be emitted from the needle into the vein? Take the pressure of blood in the vein to be 20 mmHg above that of atmospheric pressure. 0.70 N 3.3 N 0.21 N 0.24 N 1.4 N 17N
You have a tube where water enters at a velocity of 10.0 m/s, ascends 5.0 m, and then exits. The pressure pushes the water in at 250 kPa, and is measured come out at 150 kPa. The outcoming water is, faster than the incoming water. slower than the incoming water. the same speed as the incoming water.
An engine cylinder has a compression ratio (r) of 7.5, a clearance volume of 35 cm3 and a piston stroke length of 325 mm. What is the bore diameter in millimetres (mm) for the engine cylinder to the nearest mm.
A cylinder with 30 cm diameter and 100 cm length, placed vertically up, is fitted with a frictionless andleakage-free piston. Suddenly a deadweight of 5 tons is put onto the piston. How much will it go down, andwhat is the work of compression ?Please choice one below:a. 72 cm 8000 Jouleb. 80 cm. 39240 Joule.c. 20 cm 9810 Joule

SEE MORE QUESTIONS

Recommended textbooks for you

College Physics

Physics

ISBN:

9781938168000

Author:

Paul Peter Urone, Roger Hinrichs

Publisher:

OpenStax College

University Physics Volume 2

Physics

ISBN:

9781938168161

Author:

OpenStax

Publisher:

OpenStax

University Physics Volume 1

Physics

ISBN:

9781938168277

Author:

William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:

OpenStax - Rice University

College Physics

Physics

ISBN:

9781938168000

Author:

Paul Peter Urone, Roger Hinrichs

Publisher:

OpenStax College

University Physics Volume 2

Physics

ISBN:

9781938168161

Author:

OpenStax

Publisher:

OpenStax

University Physics Volume 1

Physics

ISBN:

9781938168277

Author:

William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:

OpenStax - Rice University

Principles of Physics: A Calculus-Based Text

Physics

ISBN:

9781133104261

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Physics for Scientists and Engineers

Physics

ISBN:

9781337553278

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Physics for Scientists and Engineers with Modern …

Physics

ISBN:

9781337553292

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Problem 7 Knowing that E = 29x106 psi, and v=0.30, determine the internal force in a bolt if the diameter is observed to decrease by 0.5x10¹³ in and the initial diameter is 2.5 in.