Problem 7: Determine the reactions and the force in each member of the trusses shown. Use force method of analysis. 6 m B 60 KN G ļº 60 kN H 4 panels at 8 m = 32 m D 60 kN

Q: 10. The first digital code was the: a. ASCII code b. Baudot code c. Morse code d. none of the above

A:

Q: Create a 3-dimensional isometric projection based on the 2-dimensional orthographic projection below

A:

Q: Problem Solving: 1. From the given frame shown it is supported by a hinged at A and a roller at C.…

A: To find deflection,  unit load method has been used.

Q: Map distance=5 cm Ground distance%3D2 km Determine scale

A: Given data : The value of map distance=5 cm The value of ground distance=2 Km   To find: Scale of…

Q: many futuristic projection system types, together with their parts and purposes What are they…

A: In order to aid navigators at sea and on land, maps have been created of the trade routes, local…

Q: Show Isometric View. Use Dimlinear for measurement

A: Hi! As per the honor code we are not allowed to provide file or link of the file. We are only…

Q: Problem Solving: 1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415…

A:

Q: what is means GIS

A: GIS is a tool that can be used for surveys of different fields without even physically visiting the…

Q: Why is GCMS considered a 3D analytical technique?

A: It stands for Gas chromatography - mass spectrometry. It is a method for identifying different…

Q: 1.13 List the legal requirements for registration as a land surveyor in your state. 1.14 Briefly…

A: There are different eligibility criteria to become a land surveyor. One should need to fulfill all…

Q: Find the centroid of the shaded area in the attached file Y k3cm Зст 1cm Зст 1cm 7cm

A: Schematic figure of the above problem:

Q: 99 # 日 P

A:

Q: What is the significance of Topcon's image?

A: The Significance and elaboration about topcon's image system is illustrated below.

Q: 5 TOP 10 8 FRONT ? Isometric View RSV

A:

Q: Find the areal scale for the following 3cm+09km

A: Given: Map distancex=3 cm Ground distanceX=9 km To find: Areal scale

Q: Map scale is identified as a ratio between Select one: O a. ground distance to map distance O b. map…

A: Given data : The value of distance on map=DM The value distance on ground=DG   Required : Map scale

Q: Find the scale ratio 1 cm (Map)=6 km (Ground)

A:

Q: Draw the isometric view given the orthographic views.

A:

Q: Create a 20m interval contour map.

A: The contours are the lines drawn by joining the point of similar elevation or depression such that…

Q: Define localization or site calibration?

A: localization or site calibration is defined as:

Q: Use the following 1- Fill the NGL values in the profile view. 2- Draw NGL using a vertical scale…

A: NGL: The Natural Ground Level (NGL) is defined as the unmodified level of the ground or land.…

Q: Determine centroidal coordinates of the volume. 610 mm 813 mm 1220 mm wu 099

A: Consider the figure,

Q: 70 45 -80- 160 10 Dimensions in mm

A:

Q: The previous, zoom :command is used to Its usefulness is to enlarge the drawing page. This command…

A: Shift + P is used to get previous zoom in the autocadd some times it is very useful for designing…

Q: Subject: Engineering Drawing or AutoCAD Instruction: Draw the D Drawing (ometric View) of the…

A: Isometric view is the 3 dimentional view in 2D plane.  Below is the attatched isometric view of the…

Q: 20 20 FRONT ELEVATION 60 20 60

A: For given isometric view following are top, front and side views are first angle projection views

Q: What are point positioning equations?

A: Point positioning are used for positioning with GPS. In point positioning, a GPS receiver which…

Q: Explain anti-spoofing?

A: Today's cybercriminals are continuously coming up with new strategies to enter systems and…

Q: Exercise 1.5: Third Angle Projection type is displayed. Estimate the dimensions. Draw the Visible…

A: To draw the right side view of the given figure.

Q: Sketch the othrographic views: plan view, elevation view, and end view on paper.

A: The given view is an isometric view. Taking the front direction where 12 is written, the…

Q: (Top View, Front View, Side View)

A:

Q: Q4: The original histogram of 64 x 64 image in 8 gray levels sketched below. 1. Find the histogram…

A: There are 8 gray levels, ie . K=8-1 =7 New Intensity =Cumulative frequency x K (Applying floor…

Q: Define kinematic surveying?

A: Positioning, navigational, and scheduling are the three areas into which GPS work is sometimes…

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.