Problem 7: Analyse to determine the maximum service tensile live load force that can be supported by a pair of angles 2Ls 152x102x19, shown in the accompanying figure, if A709M, Grade 345 steel and the AISC LRFD specifications are used. The live load is to be 3/2 times the dead load. The holes are drilled for 18mm rivets at standard gage distances.

Problem 7: Analyse to determine the maximum service tensile live load force that can be supported by a pair of angles 2Ls 152x102x19, shown in the accompanying figure, if A709M, Grade 345 steel and the AISC LRFD specifications are used. The live load is to be 3/2 times the dead load. The holes are drilled for 18mm rivets at standard gage distances.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a turnbuckle subjected to a load of 50 kN with permissiblestresses are in 166.67 Mpa in tension , 83.33MPa in shear and 166.67 MPa incrushing. (Please provide a handwritten solution, thank you)
The bracket shown in the figure is bolted a ceiling beam to support a fluctuating vertical load imposed on it. The bolts are -in coarse-thread SAE grade 8, tightened to recommended preload for nonpermanent assembly. The stiffnesses have already been computed and are kp=4 Mlb/in and km = 16 Mlb/in. Laad line F. Steady stress (a) Assuming that the bolts, rather than the welds, govern the strength of this design, determine the safe repeated load that can be imposed on this assembly using the Goodman criterion with the load line in the Figure and a fatigue design factor of 2. (b) Compute the static load factors based on the load found in part (a). (ie. Yielding factor of safety, Load factor of safety and factor against joint separation)
(b)Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also gIven pitch = 8mm and coefficient of friction is 0.15?
A press with screw with ACME threads shown in Figure 2 has a rate load of 1500 N. The outside diameter of ACME screw is 30 mm, and its pitch is 3.5 mm. Coefficients of friction are u = 0.1 for the threads and le =0.15 for the collar. The collar diameter de = 23 mm. A force F= 30 N is applied at end the handle to operate the press, Design the length of the handle, L. 西意 P= 30 N | 500 N
Pravinbhai
Urgent
Problem parameters for Case #2: Cases Load (lbs) 2 55,000 What is the total Deformation in (in) on the rod? Note: • Give your answer rounded to 3 decimal place i.e. 0.04352 = 0.044 or 0.04342 = 0.043 • Do NOT include any units or other text. The size of your numeric value should be given in (in). i.e. if your answer is 0.043 (in) then enter this as "0.043" (Do NOT enter "0.043 in")
The figure shows a section of a large coupling. Each bolt in this joint is subjected to cyclic load fluctuating between 0 and 13 kN. The members are made from steel. The members have equal thicknesses and total length of members is L=37 mm. Each bolt is initially tightened carefully to 78% of proof load. The bolt is to be Metric grade 5.8 M12x1.75 (coarse-pitch series). The threads has been manufactured by rolling and reliability for bolts is 95%. Calculate the stiffness of the bolt (in kN/mm). Yanıt:
The eye screw, shown in the figure below is subjected to a force of 35 kN. The material of the screw is steel with ??=355 ???. The safety factor is 1,5. Calculate the minimum diameter of the thread.
Answer is closer to 32 kN/m, but how does it get there?
Figure Q1 shows a structure under a concentrated force of P. Pins A, B, E, and F are single-shear with a 21-mm diameter. The connections at D is double shear connection with a 21-mm diameter. All pins are made of Aluminum 2014-T6. Based on yield stress, minimum factor of safety is 1.5 for all parts of below structure. Determine maximum concentrated force P, that can apply on the structure. (The cross sectional area of members EA and FB are 330 mm² and 250 mm² respectively). 350 mm 600 mm 900 mm E Copper Brass C83400 F Copper Bronze C86100 Figure Q1 A B 720 mm P D
Q2/ Calculate the maximum axial stress for a 40-ft joint of 11.75-in, 60 lbm/ft, J-55 casing with short threads coupling. Where the casing is subjected to 280000 lb, axial tension load in a portion of a directional wellbore with dogleg severity of 2"/50 ft. In case of: (1)Uniform contant between the casing and the borehole wall. (2)Assuming contant between borehole wall and the casing only at the couplings,andF n+ (3)Calculate the joint setrength of the API round thread couplings.(oult = 75000 psi, wall thickness 0.489-in, Pc= 2660 psi. o yb-952000 lb, Fj-649 000 lbf).