Problem 5: The stresses on the x-y-axes are o, = 8 ksi, o, = 12 ksi, and T = -5 ksi. Draw the Mohr's circle for this stress state. Identify the maximum shear stress from the Mohr's circle, and draw the maximum shear stress element, specifying its orientation.

Problem 5: The stresses on the x-y-axes are o, = 8 ksi, o, = 12 ksi, and T = -5 ksi. Draw the Mohr's circle for this stress state. Identify the maximum shear stress from the Mohr's circle, and draw the maximum shear stress element, specifying its orientation.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stress matrix of a point is given below. Determine the maximum shear stress at the point.
Problem 2. [Concepts: Internal forces in 2D and average normal stress] The bars of the truss each have a cross-sectional area of 1.25 in². a) Determine the average normal stress in each member due to the loading P = 8 kip. State whether the stress is tensile or compressive. b) If the maximum average normal stress in any bar is not to exceed 20 ksi, determine the maximum magnitude P of the loads that can be applied to the truss. 4 ft 4 ft 4 E 0.75 P 0
Solve alll subparts b, c, d and e B) determine the principal plane (for σmax) in radians. C) Determine the shearing stress in a plane, which is 330 with the vertical (clockwise). D) determine the normal stress (in MPa) in a plane, which is 330 with the vertical (clockwise). E) determine the minimum values of θ (in radians) for which the normal stress is the equal to or less than 35.2 MPa.
3
Determine maximum principal stress
Consider a point in a structural member that is subjected to plane strèss. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S= 24 MPa, Sy= 34 MPa, and Sy= 31 MPa. (a) Determine the principal stresses (o,1 > O2) and the maximum in-plane shear stress Tmax acting at the point. (b) Find the smallest rotation angle 0, (counterclockwise is positive, cločkwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) Answers: MPа. MPa. Op2 = MPa. Imax =
Please help me with this question.
Consider the state of plane stress shown. (Hint: Consider both in-plane and out-of-plane shearing stresses.) 7 ksi Determine the maximum shearing stress when ox- 18 ksi and ay = 8 ksl. The maximum shearing stress is ksi.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 37 MPa, Sy = 10 MPa, and Sxy = 41 MPa. (a) Determine the principal stresses (6,] > 6,2) and the maximum in-plane shear stress Tmax acting at the point. (b) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) Answers: MPa. Opl = MPa. Op2 = Tmax = MPa.
All forces applied in the system are in the (x - y) plane. The material point B at the top of the beam is rotated at an angle of 15° counterclockwise. It is required that the shear stress is 12.5 MPa for this rotated material point B. At the bottom point A of the beam it is required that the maximum tensile stress is 110 MPa. Determine the load P and the length d that satisfies these constraints defined for points A and B. Given data: L = 4 b, t = b / 25, c = 2b, b = 600 mm, e = 5 , f = 12
A.