Problem 4.50 The chain AB exerts a force of 20 lb on the door at B. (Figure 1) Figure 1 of 1 20 4 ft 3 ft A 3 ft F = 20 lb B Part A Determine the magnitude of the moment of this force along the hinged axis of the door. Express your answer to three significant figures and include the appropriate units. M₂ = Submit μA Value Units My Answers Give Up Provide Feedback Continue

Problem 4.50 The chain AB exerts a force of 20 lb on the door at B. (Figure 1) Figure 1 of 1 20 4 ft 3 ft A 3 ft F = 20 lb B Part A Determine the magnitude of the moment of this force along the hinged axis of the door. Express your answer to three significant figures and include the appropriate units. M₂ = Submit μA Value Units My Answers Give Up Provide Feedback Continue

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the magnitude and direction of the resultant forces system shown in Figure. (use component method) 100 N 150 233 80 N 100 N X
Figure 1 ✓of 1 L45° D 60° 4 m A If load C has a mass of 380kg, determine the required minimum diameter of the solid L2-steel rod AB to the nearest mm so that it will not buckle. Use F. S.= 1.94 against buckling. (Figure 1) Express your answer with the appropriate units. d = Li μA Value Submit Units My Answers Give Up ? Provide Feedback Continue
The 30-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure 1) Determine the displacement of end C with respect to the fixed support at A. Express your answer to three significant figures and include the appropriate units. HA ? Value Units Submit My Answers Give Up Provide Feedback Continue Figure 1 + of 1 600 mm 400 mm 50 kN 40 kN В C 50 kN
urces Consider the force shown in (Figure 1) Figure F-750 N 10f1 Part A Express the force as a Cartesian vector. Enter the components of the force separated by commas. Express your answers in newtons to three significant figures. F.F.F.- Submit Provide Feedback VAZ Ivec Previous Answers Request Answer N Next >>
An aluminum bar having a cross-sectional area of 0.5 in2 carries the axial loads applied at the positions shown in the figure. Assume the bar is suitably braced to prevent lateral buckling. Compute the total change in length of the bar if E = 10 × 10^6 psi.
Please make it complete solution so I can study it myself. Thank you!
Replace the loading acting on the frame by an equivalent resultant force and specify where the resultant's line of action intersects member AB (Figure 1). Suppose that F₁ = 200 lb, F2 = 100 lb, and M = 400 lb. ft. Figure x F₂ M 30⁰ -3 ft B 2 ft 4 ft 1 of 1 Determine the magnitude of the resultant force. Express your answer in pounds to three significant figures. FR = Submit Part B 0 = Submit Part C Determine the angle between the resultant force and the x axis. Express your answer in degrees to three significant figures. y = ΠΑΣΦ Submit Provide Feedback Request Answer ↓↑ ΑΣΦ Request Answer ΑΣΦ vec ↓↑ vec Specify where the resultant's line of action intersects member AB, measured from A. Express your answer in feet to three significant figures. Request Answer ? vec ? lb O , measured counterclockwise from the positive x axis ft below A
Question 1 A brass bar AB projecting from the side of a large machine is loaded at end B by a force P = 6000 N acting with an eccentricity e = 1.14 cm (Figure 1). The bar has a rectangular cross section with height h = 3 cm and width b = 1.5 cm. What is the longest permissible length Lmax of the bar if the deflection at the end is limited to 0.3 cm? (For the brass, use E = 110 GPa.) A Brass bar L Ab Figure 1 B P
Refer to the beam loaded as shown. What is the value of Ay?
A plastic cylinder is held snugly between a rigid plate and a foundation by two steel bolts (see figure). Steel L bolt Data for the assembly are as follows-length L = 600 mm, pitch of the bolt threads p = 1.0 mm, modulus of elasticity for steel E. = 960 mm2. = 195 GPa, modulus of elasticity for the plastic E, = 2.6 GPa, cross-sectional area of one bolt A. = 36.0 mm2, and cross-sectional area of the plastic cylinder A. Determine the compressive stress in the plastic when the nuts on the steel bolts are tightened by one complete turn. (Enter the magnitude in MPa.) 16905.96 X MPa
Consider the toggle clamp shown in (Figure 1) Figure 1 ▾ of 1 ¯ -235 mm 30 mm 30 mm 70 mm 130 275 mm E Part A If a clamping force of 250 N is required at A, determine the magnitude of force F that must be applied to the handle of the toggle clamp. Express your answer to three significant figures and include the appropriate units. F = O I Submit μA Value Units My Answers Give Up ? Provide Feedback Continue
Must include the free body diagram. Urgent