PROBLEM 4.3A horizontal platform with a diameter of 8 m revolves about its center at 20rpm. Find the tangential speed in m/s of a point at the edge of the platform.6.38 m/sb. 6.28 m/s3.с. 6.48 m/sd. 6.18 m/sа.

Answered: Image /qna-images/answer/98613e4a-e8fa-40b2-98bd-7831c9e64675.jpg

Answered: PROBLEM 4.3 A horizontal platform with…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem #4) The extremities of a 4-ft rod weighing 50lb (1.5528slugs) can move freely and with no friction along two straight tracks. The rod is released with no velocity from the position shown, resulting in the rod to slide down the incline. The angular acceleration of the rod is a = +2.30k rad/s² and the linear acceleration at point A is 12.5674ft/s² to the right. Determine (a) ao, the linear acceleration at point G, and (b) RA and RB, the normal reaction forces at point A and B. Include and present the Free Body Diagram and Inertial Response Diagram as part of the solving process. B B=45° 4 ft G O D 30°1 A
The composite shaft shown in the figure is manufacturedby shrink-fitting a steel sleeve over a brass coreso that the two parts act as a single solid bar in torsion.The outer diameters of the two parts are d1 = 40 mmfor the brass core and d2 = 50 mm for the steel sleeve.The shear moduli of elasticity are Gb = 36 GPa for thebrass and Gs = 80 GPa for the steel.(a) Assuming that the allowable shear stressesin the brass and steel are τb = 48 MPa andτs = 80 MPa, respectively, determine the maximumpermissible torque Tmax that may beapplied to the shaft.(b) If the applied torque T = 2500 kN . m, findthe required diameter d2 so that allowable shearstress τs is reached in the steel.
PROBLEM 4.6 With the aid of a string, a gyroscope is accelerated from rest to 38 rad/s in 0.5 s. What is its angular acceleration in rad/s²? c. 85 d. 95 6. а. 75 b. 65 7. How many revolutions does it go through in the process? а. 1.392 с. 1.492 b. 1.592 d. 1.692
The oscillating link OAB of a mechanism, as shown in Fig. 7.35, is pivoted at O and is moving at 90 r.p.m. anticlockwise. If OA = 150 mm; AB = 75 mm, and AC= 250 mm, calculate 5. 15° 1. the velocity of the block C; 2. the angular velocity of the link A C; 200 mm and 3. the rubbing velocities of the pins at 0, A and C, assuming that these pins are of equal diameters of 20 mm. [Ans. 1.2 m/s; 1.6 rad/s² clockwise; 21 250 mm 75 mm 200 mm/s, 782 mm/s, 160 mm/s] B 6. The dimensions of the various links of a Fig. 7.35 mechanism, as shown in Fig. 7.36, are as follows : AB = 30 mm ; BC = 80 mm ; CD = 45 mm ; and CE = 120 mm. 30° 75 mm 22.5 mm E D. Fig. 7.36
PROBLEM 4.1 The wheel of an automobile revolves at the rate of 700 rpm. How fast does it move in kilometre per hour, if the radius of its wheel is 250 mm. 6.09 kph 5.09 kph 1. c. 7.09 kph d. 8.09 kph а. b.
A shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: (a) The magnitude of the mass in plane E and its angular position relative to the mass in plane A (b) The distance of the plane E from plane A (c) The dynamic loading on each bearing when the mass in plane E has been attached and the shaft rotates at 200 rev/min. For the bearing loads in the opposite direction determine all the unknown values. For the bearing loads in the same direction, show the diagrams and equations only to use for a possible solution.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

PROBLEM 4.3 A horizontal platform with a diameter of 8 m revolves about its center at 20 rpm. Find the tangential speed in m/s of a point at the edge of the platform. 6.38 m/s 6.28 m/s 3. c. 6.48 m/s d. 6.18 m/s а. b.