Problem 4. A closed traverse has the following angles to the right at traverse station: T2 = 281° 24'; T3 = 260° 34'; T4 = 209° 53'; T5 = 272° 40'; T6 = 285° 52' If the azimuth of traverse line T2-T3 is 55° 45'. Compute for the Azimuth and Bearing of the traverse lines. What is the angle to the right at T1? Compute the azimuth and bearing of all the lines. Sketch the figure and prepare a table for your final answer.

Problem 4. A closed traverse has the following angles to the right at traverse station: T2 = 281° 24'; T3 = 260° 34'; T4 = 209° 53'; T5 = 272° 40'; T6 = 285° 52' If the azimuth of traverse line T2-T3 is 55° 45'. Compute for the Azimuth and Bearing of the traverse lines. What is the angle to the right at T1? Compute the azimuth and bearing of all the lines. Sketch the figure and prepare a table for your final answer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the given traverse, the forward direction is given by the alphabetical order of the station names. Each angle is measured clockwise from the back direction to the forward direction so that they are on the left of the traverse looking forward. Draw a sketch of the traverse and compute the final coordinates. Adjust by Transit Rule. Bearing EA: S 10°14' E Coordinates of E: N 1000.00, E 1000.00
Q1). The interior angles and lengths are given in below table, were obtained in a closed- loop traverse. The coordinates of the station A are EA (2500) m and NA (3000) m. Determine: 1- The correct coordinates of all traverse stations. 2- Area enclosed by (ACBA). Interior angle Length (m) Forward. azimuth BAE(114°35') AB(350) AB (124°0') AED(73 25') BC(700) EDC(241 40') CD(295) DCB(35°20') DE(245) CBA(75'0') EA(405) E U N B
Given a,b,c questions are subparts please answer all with clear calculations
: Work out included angles from following data : Sr. No. Line F.B. AB 40° BC 120° CD 240⁰ DA 340⁰ 160' 1 2 3 4 B.B. 220' 300' 60' 1
35. When setting out design points from control points using a total station, horizontal orientation must be undertaken to ensure that: A. The height of collimation of the total station is on the same height datum as the design and control points. B. The vertical circle of the total station is correctly orientated. C. The total station is correctly centred over one of the control points. The horizontal circle of the total station is set on the same E,N grid system as the design and control points. None of the above. D. E.
SITUATION. A close traverse has a following data: Departure -500 m Course Distance Latitude A-B 583.10 m 300 m В-С 640.31 m 400 m 500 m C-D 917.88 m 800 m -450 m D-A 783.90 m -720 m -310 m What is the corrected departure of course D- A using transit rule?
Find the intersection points for the system below: у3 — 2х — 3 —2х — 3 | x² + y² = 30 Round your answers to 2 decimal places O a) (-3.58, 4.15), (1.18, -5.35) b) (-1.18, -5.35), (3.58, 4.15) c) (-1.18, 5.35), (3.58, -4.15) O d) DNE
How many slope deflection equations are created for a beam with 6 spans?
Find the station kilometer of point B with curb radii of R1 and R2 according to the information given.
Instructions Compute and tabulate the forward and back bearings and azimuths (from north and south) of a regular icosagon. Given the first starting direction of side AB: 215 deg 25 min 42 sec from North, Station C is westerly of B.
In order to determine a tunnel between station A and B where the vision was obstructed between them, a traverse was selected to link between these stations. The field measurements of the traverse as in the table below.Calculate the length and the bearing of the tunnel (AB) and the angle BAD for * .setting it out Line Length(m) Azimuth DA 500 2100 DC 2000 450 СВ 1000 2700 АВ ? 2,
purses / OID 310 674_GMT151_1 / 19 April - 25 April / MID-TERM EXAM Which one is wrong about traversing? O a. In closed polygon traverse both starting and terminating points of the traverse coincide with each other. O b. The intervisibility between adjacent stations, forward and back, must be maintained for angle and distance measurements. Oc Open traverses are strong in terms of eliminating errors and mistakes. O d. Interior angle traverses must be turned clockwise from the backsight site to the foresight site to reduce mistakes. e. A Traverse may be of two types: Open Traverse and Closed Traverse Next page