Problem (4) When the power to an electric motor is turned on the motor reaches its rated speed of 2400 rpm in 4 s, and when the power is turned off the motor coasts to rest in 40 s. Assuming uniformly accelerated motion, determine the number of revolutions that the motor executes: (a) in reaching its rated speed, (b) in coasting to rest.

Problem (4) When the power to an electric motor is turned on the motor reaches its rated speed of 2400 rpm in 4 s, and when the power is turned off the motor coasts to rest in 40 s. Assuming uniformly accelerated motion, determine the number of revolutions that the motor executes: (a) in reaching its rated speed, (b) in coasting to rest.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You have your bicycle upside down while you adjust the chain. The chain is wound around the rear wheels small gear, which has a radius of 4.0 cm. At the pedals, the chain is wound around the large gear, which has a radius of 11.0 cm. The radius of the rear wheel is 35.0 cm. You spin the pedals initially so they finish two revolutions in 1.0 s, starting from rest. Assume constant acceleration. (a) Find the angular acceleration of the rear wheel in rad/s2. (b) Find the magnitude of the total acceleration of a point at the edge of the small gear at the end of 1.5 s (the sum of the radial and tangential accelerations). (c) What is the tangential acceleration for that point during the first second? (d) Calculate the linear acceleration of the chain.
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A simple friction drive consists of two disks A and B. Initially, disk B has a clockwise angular velocity of 550 rpm, and disk A is at rest. It is known that disk B will coast to rest in 65 s. However, rather than waiting until both disks are at rest to bring them together, disk A is given a constant angular acceleration of 3 rad/s² counterclockwise. A 2.5 in. B 3 in. Determine at what time the disks can be brought together if they are not to slip. (You must provide an answer before moving to the next part.) The disks can be brought together at t= S.
comes to rest from a speed of 72 kmh in a distance of 60 m. By using the principle of conservation of energy, cál- culate the resistive force and the decelera- tion of the car.
Question 4. A person swings a stone attached to a string in a horizontal circle of radius 2.1 m. At a particular moment in time, the stone has an angular velocity of 3.1 rad/s and an angular acceleration of 11 rad/s². Calculate: (a) the tangential acceleration, a,, of the stone: m/s² (b) the centripetal acceleration, a, of the stone: m/s² (c) the total acceleration, at, of the stone: m/s
PROBLEM 4.6 With the aid of a string, a gyroscope is accelerated from rest to 38 rad/s in 0.5 s. What is its angular acceleration in rad/s²? c. 85 d. 95 6. а. 75 b. 65 7. How many revolutions does it go through in the process? а. 1.392 с. 1.492 b. 1.592 d. 1.692
The crude-oil pumping rig shown is driven at 20 rpm. The inside diameter of the well pipe is 2 in., and the diameter of the pump rod is 0.75 in. The length of the pump rod and the length of the column of oil lifted during the stroke are essentially the same, and equal to 6000 ft. During the downward stroke, a valve at the lower end of the pump rod opens to let a quantity of oil into the well pipe, and he column of oil is then lifted to obtain a discharge into the connecting pipeline. Thus, the amount of oil pumped in a given time depends upon the stroke of the lower end of the pump rod. Knowing that the upper end of the rod at D is essentially sinusoidal with a stroke of 45 in. and the specific weight of crude oil is 56.2 lb/ft3 determine (a) the output of the well in ft3. /min if the shaft is rigid, (b ) the output of the well in ft3 /min if the stiffness of the rod is 2210 N/m, the equivalent mass of the oil and shaft is 290 kg, and damping is negligible.
explain it and answer
3. The normal component of acceleration represents a. the time rate of change in the magnitude of the velocity b. the time rate of change in the direction of the velocity c. magnitude of the velocity d. directions of the total acceleration
The rotor of a gas turbine is rotating of 12 rad/s when the turbine is shut down. It is observed that 4 min is required for the rotor to coast to rest. Assuming uniformly accelerated motion, determine the number of revolutions that the rotor executes before coming to rest
In a cam-follower mechanism, if the ratio of maximum acceleration during upward and downward motion is 3.6, then the ratio of outward angle to return angle is approximately О а. 0.277 b. O b. 0.527 О с. 1.26 O d. 3.6
Two friction discs A and B will come into contact, without slipping, when the angular velocity of disc A is 320 rpm counterclockwise. Disk A starts from rest at t = 0 and has a constant angular acceleration with magnitude a. Disk B starts from rest at time t = 4 s and has a constant angular acceleration in a clockwise direction, also with a magnitude a. Determine the magnitude of the required angular acceleration a, in rad/ s². B 150 mm 200 mm
4. Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is the angular velocity of each pulley if the belt has a constant speed of 5 m/s? What is the frequency and the period of each pulley? (1 (b) What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s in 10 s? How many revolutions does the pulley turn in that time? (^^. R₁ = 0.3 m R₂ = 0.2 m R₂ R3 = 0.1 m R3 R₁