PROBLEM 4: The steel framework is used to support the 100mm reinforced lightweight concrete slab that carries a uniform live loading of 25 kN/m². Sketch the loading that acts along members BE and FD. Set b = 3m, a = 2.4m (Hint: see the Table for Dead Loads) C B Answer: Reaction @B: 57.2kN Reaction @F: 95.4 kN

PROBLEM 4: The steel framework is used to support the 100mm reinforced lightweight concrete slab that carries a uniform live loading of 25 kN/m². Sketch the loading that acts along members BE and FD. Set b = 3m, a = 2.4m (Hint: see the Table for Dead Loads) C B Answer: Reaction @B: 57.2kN Reaction @F: 95.4 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A channel-section has the dimensions as shown. Consider a cantilevered beam subjected to an end force P. L = 100 cm a) iif cross-section las is used, determine its normal stress distribution. (a) (b) b) if you stack two las sections as a box, but leave a gap between them, two sections carry = loadings with the same distribution pattern. Try express the results. (C) 2ª L 2CM дом E 2ch weld
3.1 Show your complete solution.
Q2) For single story building shown in Figure below, all beams are 300x500 mm, all columns are 300x300 mm. The building subjected to dcad load 3 KN/m and the roof live load 8 KN/m 5 m 0.3 a. The slab thickness for deflection control. b. Check the shear adequacy of the slab. c. By using Ø 12 mm, what is the required 12 m positive reinforcement at section A-A?. d. If the top reinforcement at section B-B is Ø 12 mm @ 200 mm, show if this reinforcement is adequate to support the applied load? e. Find the maximum applied load on beam A &B 0.3 B 12 m 0.3 12e200 53m 5.30 m Good Luck 1 045
The steel beam has the cross section shown. The beam length is L = 5.6 m, and the cross-sectional dimensions are d = 335 mm, bf = 195 mm, tf = 12 mm, and tw = 10 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 165 MPa. Wo X Answer: Wo= 12 B 72 C kN/m
Rectangular reinforced concrete beam section b = 40 cm, h = 60 cm, d = 53 cm, material strength fy = 4200 = 4200 kgf / cm^2, fc ' = 280 kgf/cm^2, beam section configuration #4 For closed stirrups @15 cm, the net cover is 4 cm, and the beam section is subjected to a torque of Tu = Tcr. Q: What is the ultimate shear load value Vu that the beam section can bear. Among them, Tcr is the cracking torque of the beam section, #4 steel bar (db=1.27 cm, Ab=1.267 cm^2).
A distributed load of w N/m is applied over an entire length of a simply supported beam 8m long. The beam section is made up of four 20mmx100mm rectangles arranged as shown. Determine the following: a. maximum value of w without exceeding the permissible flexure stress of 10MPa. b. maximum value of w without exceeding the permissible shear stress of 1.2MPa. c. maximum value of w without exceeding the permissible screw strength of 800N for a pitch of 75mm.Please show your clean and complete solution. Thanks
A square hollow steel structure with a wall thickness of t1 = 10 mm is pin linked to two gusset plates with a thickness of t2 = 12 mm, which are welded to a base plate with a thickness of 12 mm and secured to a concrete base with 4-16 mm diameter anchor bolts. The pin has a diameter of 16 mm. P = 48 kN compressive load, 30 deg. P= 48 kN Stnt gusset plate fy=12 mm 0=30 10 m 12 mm 16 mm ø anchor bolt 4-16 mm p 1. Determine the bearing stress in MPa between the struct and the pin. 2. Calculate the pin's shear stress in MPa. 3. Determine the anchor's shear stress in MPa.
The steel beam has the cross section shown. The beam length is L = 7.5 m, and the cross-sectional dimensions are d = 385 mm, b = 190 mm, t+= 12 mm, and tw = 10 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 155 MPa. Wo -1/2 Answer: Wo= B sla -1/12 kN/m
Example 1 A rectangular concrete beam 300 mm wide and has an effective depth of 450 mm. What is the design moment capacity of the beam according to the ACI code? Use fe = 27.6 MPa & fy = 413 MPa, Use: 0.003 Pmax = 0.85 x B1 x- fy 0.003 + 0.005 b= 300 mm d =63 mm 2 # 29 d= 450 mm 4 # 32
The steel beam has the cross section shown. The beam length is L = 7.3 m, and the cross-sectional dimensions are d = 300 mm, bf = 180 mm, tf = 13 mm, and tw = 7 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 250 MPa.
4
A simply supported wood beam with a span of L = 15 ft supports a uniformly distributed load w. The beam width is b = 7 in. and the beam height is h = 13 in. The allowable bending stress of the wood is 860 psi. Determine the magnitude of the maximum load w that may be carried by the beam. b Answer: w = i lb/ft.