Problem 4) mp M m Consider the pulley system above. The acceleration of the system is 2 m/s? along the arrows shown. The mass of the pulley, m, is 5 kg. The small mass has a mass of 3 kg. a) Draw a free body diagram of the masses m and M. Label all forces b) Consider the pulley and use torque equations. Solve for the difference in the tensions, T2-T1. c) Solve for mass M. One way this can be done is to write the net force equations based on the free body diagrams for m and M, making sure "positive" forces are in the direction of motion. Then add the equations together, and substitute your answer from part (b).

Problem 4) mp M m Consider the pulley system above. The acceleration of the system is 2 m/s? along the arrows shown. The mass of the pulley, m, is 5 kg. The small mass has a mass of 3 kg. a) Draw a free body diagram of the masses m and M. Label all forces b) Consider the pulley and use torque equations. Solve for the difference in the tensions, T2-T1. c) Solve for mass M. One way this can be done is to write the net force equations based on the free body diagrams for m and M, making sure "positive" forces are in the direction of motion. Then add the equations together, and substitute your answer from part (b).

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Nilo
Q2 Problem 2 Problem 2 Calculate the net torque on the square shown below about the axis through its center. The three forces pictured are the only forces on the square. 3ON 20N ISN 450 20 cm
5. The figure below illustrates an Atwood's machine. Let the masses of blocks A and B be 4.00 kg and 2.00 kg, respectively, the moment of inertia of the wheel about its axis be 0.100 kg.m² and the radius of the wheel be 0.500 m. a) Find the linear acceleration of block A and block B if there is no slipping between the cord and the surface of the wheel b) Find the tension in right side of the cord if there is no slipping between the cord and the surface of the wheel c) Find the tension in left side of the cord if there is no slipping between the cord and the surface of the wheel.
Don't provide hand writing solution
The automobile has a mass of 2.2 Mg and center of mass at G. Take u, = 0.3. (Figure 1) Part A Determine the towing force F required to move the car if the back brakes are locked, and the front wheels are free to roll. Express your answer to three significant figures and include the appropriate units. HA ? F = Value Units Submit Request Answer Provide Feedback Figure 1 of 1 G. 0.6 m 0.3 m B A 1m-1.50 m- 0.75 m
A 5.7 g quarter sits 25 cm from the axis of rotation on a turntable that has a period of rotation of 1.8 seconds. a) Draw a free-body diagram showing the forces involved. b) What is the weight of the quarter inNewtons? Round to the nearest hundredth. c) What is the NORMAL FORCE acting on the quarter. d) Determine the coefficient of static friction be in order to keep the quarter from sliding outward when the turntable is in motion?
For the wheel and axle system shown below, which of the following expresses the condition required for the system to be in static equilibrium? a.) am2=bm1 b.) m1=m2 c.) am1=bm1 d.) a^2m1=b^2m2
3 Torque A 16 cm, 10 g pencil, with mass evenly distributed along its length, is held horizontally at rest between a person's thumb and index finger as shown. The index finger touches the pencil 2 cm from its end and the thumb touches it 4 cm from the same end. Index Finger 2 cm cm 10 g Thumb Problem 3.1. If the thumb and index finger exert vertical forces only, what is the magnitude and direction of each of these forces?
2) A bucket of water is suspended at the end of a rope wrapped around a pulley. The pulley is pivoted on a frictionless axle passing through its center. The axle is attached to the ceiling. The bucket is released from rest and falls a distance of H. The inertia of the pulley is I = ½ MR?. M a. On the diagram above, show all the forces applied on the bucket and 'R pulley. b. Determine the linear acceleration of the bucket. c. Determine the angular acceleration, a of the pulley. d. Determine the tension force in the rope. m e. Determine the speed of the bucket at the end of distance H. f. Determine the force exerted on the pulley by the axle.
For each of the situations below, determine which forms of Newton's second law (N2L) are appropriate: N2L rotation, N2L translation, either, or both. You are asked to find the angular acceleration of a low-friction pulley with a given force exerted on it. You are asked to find the angular acceleration of a low-friction pulley due to a mass hanging from it by a rope. You are asked to determine the maximum height of a spinning ball that is thrown upwards. You are asked to calculate the time it takes a ball to roll down an inclined plane. You are asked to find the tangential acceleration of a small satellite in a circular orbit that results from it firing its thruster. You are asked to determine the orbital period of a small satellite around Earth.
18 Part A In (Figure 1), what is the net torque about the axle? Express your answer using two significant figures and include the appropriate units. HẢ ? デ= Value Units Submit Request Answer Provide Feedback Figure < 1 of 1 30 N 4.0 cm 20 N
Ferrari Testarossa uses a single lug nut.The bolts on a normal car wheel require tightening to a torque of 90N∙m. If a 30 cm long wrench is used, what is the magnitude of theforce required when the force is perpendicular to the wrench?A) 300 NB) 150 NC) 30 ND) 15 N