PROBLEM 3.23 240 mm Two solid shafts are connected by the gears shown. A torque of magnitude T = 900 N m is applied to shaft AB. Knowing that the allowable shearing stress is 50 MPa and considering only stresses due to twisting, determine the required diameter of (a) shaft AB, (b) shaft CD. 80 mm dAR = 2c = 45.1 mm dcp =2c = 65.0 mm

PROBLEM 3.23 240 mm Two solid shafts are connected by the gears shown. A torque of magnitude T = 900 N m is applied to shaft AB. Knowing that the allowable shearing stress is 50 MPa and considering only stresses due to twisting, determine the required diameter of (a) shaft AB, (b) shaft CD. 80 mm dAR = 2c = 45.1 mm dcp =2c = 65.0 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: If the allowable shear strength of aluminum is 45 MPa, determine the minimum thickness, t, of the…

Q: The stepped shaft shown rotates at 430 rpm. Knowing that r=0.5 in., determine the maximum power that…

A: Given: r=0.5 inN=430 rpmτmax=7500 psi

Q: The two solid shafts are connected by gears as shown and are made of a steel for which the allowable…

A: The given information in the problem is shown in the following attached image:

Q: A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to a…

A: Given data: The angle of twist, θ=3°. The length of shaft, L=6 m. The applied torque, T=12 kN·m.…

Q: Q.2) Three solid Brass (G = 44 GPa) shafts along with two sets of meshing gears are used to form…

Q: 22 mm For the cylindrical shaft shown, determine the maximum shearing stress caused by a torque of…

Q: Using Tall = 8.7 ksi and knowing that G= 5.6 x 106 psi, determine for each of the cold-rolled yellow…

Q: Knowing thát the internal diameter of the HolUW SIlat shown is d= 23 mm, determine the maximum shear…

Q: For the assembly of Fig. , knowing that rA= 2rB, determine the angle of rotation of end E of shaft…

A: Given that The relation between the radius is, rA = 2rB. Let TAD be the torque exerted on shaft AD.…

Q: The largest torque Tc that can be applied at Cis kip-in.

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A: Note:- here last question is not related to main question. As per honor code and answering…

Q: 2. a. Knowing that the allowable shearing stress is 8ksi, for the stepped shaft shown, determine the…

A: Step 1: Step 2: Step 3: Step 4:

Q: 3) The electric motor exerts a torque of 600 N.m on the steel shaft ABCD when it is rotating at a…

A: Given Data Modulus of rigidity is : G=77 GPa Length section of BC is : LBC=0.8 m Length section of…

Q: PROBLEM 3.52 A 4 kNm torque T is applied at end A of the composite shaft shown. Knowing that the…

Q: Knowing that d = 1.2 in., determine the torque T that causes a maxi-mum shearing stress of 7.5 ksi…

Q: 2- The design of the gear-and-shaft system shown requires that steel shafts of the same diameter be…

A: or 0.0262 radG = 77 GPa

Q: (a) For the solid steel shaft shown, determine the angle of twist at A. Use G=11.2 × 106 psi. (b)…

A: Given data: The applied torque is, T = 60 kipˑin. The inner diameter, di = 0.75 in. The outer…

Q: Q3: The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques as…

A: To find: The total angle of twist at end A. Given: The modulus of rigidity of the shaft is G=77 GPa.…

Q: 4. The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A…

Q: 100 mm 75 mm 150 mm 200 mm 100 mm 150 mm 100 mm CE PROBLEM 8.29 The solid shaft AE rotates at 600…

Q: The torque T causes a rotation of 2° at end B of the stainless-steel bar shown. Knowing that b = 20…

A: The rotation of the bar is .The distances are given as-The length of the bar is .The shear modulus…

Q: A circular shaft AB consists of a 10-in.-long, 78-in.-diameter steel cylinder, in which a…

A: Given data: The applied torque, T = 90 lbˑ The diameter of rod at A is, dA = 78 in. The diameter of…

Q: 1. (a) Determine the maximum shearing stress caused by a 80- kip x in. torque T in the…

A: Given Data Torque = 80 kip. in Diameter, D=3 in Length of the steel shaft, L=4ft

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

PROBLEM 3.23
240 mm
Two solid shafts are connected by the gears shown.
A torque of magnitude T = 900 N m is applied to shaft
AB. Knowing that the allowable shearing stress is 50 MPa
and considering only stresses due to twisting, determine
the required diameter of (a) shaft AB, (b) shaft CD.
80 mm
dAR = 2c = 45.1 mm
dcD = 2c = 65.0 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3.36 The torques shown are exerted on pulleys B, C, and D. Knowing that the entire shaft is made of aluminum (G = 27 GPa), deter- mine the angle of twist between (a) C and B, (b) D and B. 30 mm 30 mm 400 N- m GG 36 mm 900 N- m 36 mm 500 N. m B "0.6 m E. 0.5 m D m 0.5 Fig. P3.36
The design of a machine element calls for a 40-mm-outer diameter shaft to transmit 45 kW. (a) If the speed of rotation is 720 RPM, determine the maximum shearing stress in shaft a. (b) If the speed of rotation can be increased 50 % to 1080 RPM, determine the largest inner diameter of shaft b for w/c the maximum shearing stress will be the same in each shaft.
! Required information The torques shown are exerted on pulleys A and B. Consider TA = 360 N·m and Tg = 400 N.m. TA 30 mm TB 46 mm OXX Knowing that both shafts are solid, determine the maximum shearing stress in shaft BC. MPa. The maximum shearing stress in shaft BC is
b) The torques shown in Fig. Q1(b) are exerted on pulleys A, B, C and D. Knowing that each shaft is solid, 120 mm long and made of steel with Modulus of Rigidity of 77 GPa and Modulus of Elasticity of 70 GPa i) Compute the angle of twist between A and C with the aid of free body diagrams. i1) State the direction of the twist (either clockwise or counterclockwise) for question Q1(b)i. 120 N-m 90 N-m D 60 N-m 20 mm C 15 N-m 15 mm 10 mm Fig. Q1(b)
A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to a torque of 12 KN*m. The modulus of rigidity of the steel shaft is 83 GPa. Determine; a) Diarneter of the shaft. (. b) Maximum shearing stress developed in the shaft.
! Required information The torques shown are exerted on pulleys A, B, and C, where T₁ = 3 kip-in. and 72 = 7.4 kip-in. Assume that both shafts are solid and the diameter of shafts AB and BC to be 1.3 in. and 1.8 in., respectively. T1 10.4 kip.in. 48 in. B 72 in. T2 C Determine the maximum shearing stress in shaft AB. The maximum shearing stress in shaft AB is ksi.
! Required information The torques shown are exerted on pulleys A and B. Consider TA = 360 N·m and TB = 400 N.m. TA 30 mm 46 mm B Knowing that both shafts are solid, determine the maximum shearing stress in shaft AB. The maximum shearing stress in shaft AB is MPa.
Pravinbhai
A 0.75" diameter solid steel shaft is connected by the steel bolted coupling shown. The maximum allowable shear stress in the steel is 18 ksi (shaft and bolts). The coupling consists of steel bolts that are 1/8" diameter and the bolt holes are equally spaced and centered on a 4" diameter circle (2" radius from the center of the shaft to the center of a bolt hole). Determine a) The maximum torque that the shaft can carry Ans: /,491"* b) The number of bolts required for the torque in part a). Assume the bolts fail by shearing at the coupling interface and the shear stress is uniform across the bolt's cross sectional area.
The allowable shearing stress is 15 ksi in the 1.5-in.-diameter steel rod ABand 8 ksi in the 1.8-in.-diameter rod BC. Neglecting the effect of stress concentrations, determine the largest torque that can be applied at A
A torque T= 50 kip-in. is applied at end A of the composite shaft shown. Know that the modulus of rigidity is 11.2 x 10 psi for steel and 4 x 106 psi for aluminum. 3 in. 24in. 100 in. Steel Aluminum Determine the maximum shearing stress in the steel core.