100 mm 75 mm 150 mm 200 mm 100 mm 150 mm 100 mm CE PROBLEM 8.29 The solid shaft AE rotates at 600 rpm and transmits 45 kW from the motor M to machine tools connected to gears G and H. Knowing that Tall = 55 MPa and that 30 kW is taken off at gear G and 15 kW is taken off at gear H, determine the smallest permissible diameter of shaft AE.

100 mm 75 mm 150 mm 200 mm 100 mm 150 mm 100 mm CE PROBLEM 8.29 The solid shaft AE rotates at 600 rpm and transmits 45 kW from the motor M to machine tools connected to gears G and H. Knowing that Tall = 55 MPa and that 30 kW is taken off at gear G and 15 kW is taken off at gear H, determine the smallest permissible diameter of shaft AE.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: If the allowable shear strength of aluminum is 45 MPa, determine the minimum thickness, t, of the…

Q: A 88-N-m torque is applied to a hollow shaft having the cross section shown. Neglecting the effect…

A: The torque applied is

Q: The two solid shafts are connected by gears as shown and are made of a steel for which the allowable…

A: The given information in the problem is shown in the following attached image:

Q: Q.2) Three solid Brass (G = 44 GPa) shafts along with two sets of meshing gears are used to form…

Q: Using Tall = 8.7 ksi and knowing that G= 5.6 x 106 psi, determine for each of the cold-rolled yellow…

Q: hollow brass (6000 ksi) shaft CD and a thin-walled steel (G=12000 ksi) tube DE. The whole assembly…

A: Find out:Maximum shear stress in the bolts at C (ksi)Maximum shear stress in the bolts at D (ksi)The…

Q: The driveshaft of an automobile is being designed to transmit 172 hp at 2950 rpm. Determine the…

Q: Knowing thát the internal diameter of the HolUW SIlat shown is d= 23 mm, determine the maximum shear…

Q: For the assembly of Fig. , knowing that rA= 2rB, determine the angle of rotation of end E of shaft…

A: Given that The relation between the radius is, rA = 2rB. Let TAD be the torque exerted on shaft AD.…

Q: 3. Gear B supplies 20 KW of power, while gears A, Cand D withdraw 6 kW, 4 kW and 10 kW,…

A: Answer: The required minimum diameter of the shaft is 24.5 mm.

Q: 2. A brass sleeve with an inner diameter of 200mm and an outer diameter of 300mm is pressed onto a…

A: Given DataP=16.8MPaEb=110GPavb=0.32Es=210GPavs=0.30r=100+δmmdi=200mmdo=300mm

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A: if you have any doubts please comment

Q: 3) The electric motor exerts a torque of 600 N.m on the steel shaft ABCD when it is rotating at a…

A: Given Data Modulus of rigidity is : G=77 GPa Length section of BC is : LBC=0.8 m Length section of…

Q: 2- The design of the gear-and-shaft system shown requires that steel shafts of the same diameter be…

A: or 0.0262 radG = 77 GPa

Q: e of rotation of end A of the gear-and-shaft system? unit of Degree)

Q: Three shafts and four gears are used to form a gear train that will transmit 6.7 kW from the motor…

A: Detailed step by step solution is given below, still if you have any query please feel free to…

Q: d₁ = 38 mm d₂

Q: Using Tall = 7.95 ksi and knowing that G= 5.6 x 106 psi, determine for each of the cold-rolled…

A: Given dataAllowable shearing stress=7.95 KsiG=modulus of rigidity=L=Length of the bar= 16 inFind,1)…

Q: 4. The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A…

Q: Two solid shafts are connected by gears as shown. Knowing that G = 77.2 GPa for each shaft,…

A: The modulus of rigidity of shafts are .The torque applied is

Q: Using Tall = 69 MPa and G = 27 GPa, determine for each of the aluminum bars shown the largest torque…

Q: 3. (Problem 3.35 from the text book) The electric motor exerts a 500-N m torque on the aluminum…

Q: The solid circular shaft shown is made of a steel that is assumed to be elastoplastic with Ty= 145…

A: The answer is provided below

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.

Question

100 mm
75 mm
150 mm
200 mm
100 mm
150 mm
100 mm
CE
PROBLEM 8.29
The solid shaft AE rotates at 600 rpm and
transmits 45 kW from the motor M to machine
tools connected to gears G and H. Knowing that
Tall = 55 MPa and that 30 kW is taken off at gear
G and 15 kW is taken off at gear H, determine the
smallest permissible diameter of shaft AE.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: all given data are in this step

VIEW

Step 2: detail solution are in this step

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular shaft AB consists of a 10-in.-long, 78-in.-diameter steel cylinder, in which a 5-in.-long, 58-in.-diameter cavity has been drilled from end B. The shaft is attached to fixed supports at both ends, and a 90 lb?ft torque is applied at its midsection . Determine the torque exerted on the shaft by each of the supports.
3.36 The torques shown are exerted on pulleys B, C, and D. Knowing that the entire shaft is made of aluminum (G = 27 GPa), deter- mine the angle of twist between (a) C and B, (b) D and B. 30 mm 30 mm 400 N- m GG 36 mm 900 N- m 36 mm 500 N. m B "0.6 m E. 0.5 m D m 0.5 Fig. P3.36
b) The torques shown in Fig. Q1(b) are exerted on pulleys A, B, C and D. Knowing that each shaft is solid, 120 mm long and made of steel with Modulus of Rigidity of 77 GPa and Modulus of Elasticity of 70 GPa i) Compute the angle of twist between A and C with the aid of free body diagrams. i1) State the direction of the twist (either clockwise or counterclockwise) for question Q1(b)i. 120 N-m 90 N-m D 60 N-m 20 mm C 15 N-m 15 mm 10 mm Fig. Q1(b)
Pravinbhai
UNIVERSITY of Prince Edward ISLAND i mm GGGG 54 mm T₁-1.2 kN-m 1-08 kNm 0 154 T-0.1 kN m 40 mm ASSIGNMENT 2.6 Under normal operating conditions, the electric motor exerts a torque of 2.4 kN m on shaft AB. Knowing that each shaft is solid, determine the maximum shearing stress in (a) shaft AB, (b) shaft BC, (c) shaft CD. ASSIGNMENT 2.7 Two shafts, each of -in. diameter, are connected by the gears shown. Knowing that G=11.2 x 10 psi and that the shaft at F is fixed, determine the angle through which end
A motor running at 1800 rpm transmits 10 KW of power through a 25 mm diameter shaft 1.2 m long. What is the angle of twist in the shaft? G = 8.3 x 1010 Pa. A. 1.14° С. 1.34° В. 1.59° D. 1.04°
A 0.75" diameter solid steel shaft is connected by the steel bolted coupling shown. The maximum allowable shear stress in the steel is 18 ksi (shaft and bolts). The coupling consists of steel bolts that are 1/8" diameter and the bolt holes are equally spaced and centered on a 4" diameter circle (2" radius from the center of the shaft to the center of a bolt hole). Determine a) The maximum torque that the shaft can carry Ans: /,491"* b) The number of bolts required for the torque in part a). Assume the bolts fail by shearing at the coupling interface and the shear stress is uniform across the bolt's cross sectional area.
Under normal operating conditions, the electric motor exerts a torque of 2.4 kN·m on shaft AB. Each shaft is solid with diameter d 52 mm. In order to reduce the total mass of the assembly, a new design is being considered in which the diameter of shaft BC will be smaller. Determine the smallest diameter of shaft BC for which the maximum value of the shearing stress in the assembly will not be increased. The smallest diameter of shaft BC is mm.