Problem 3.1. A 1-in.-diameter solid bar (1), a square solid bar (2), and a circular tubular member with 0.2-in. wall thickness (3), each supports an axial tensile load of 5 kips. (a) Determine the axial stress in bar (1). (b)If the axial stress in each of the other bars is 6 ksi, what is the dimension, b, of the square bar, and what is the outer diameter, c, of the tubular member? t = 0.2 in. 1 in. (1) (2) (3)

Problem 3.1. A 1-in.-diameter solid bar (1), a square solid bar (2), and a circular tubular member with 0.2-in. wall thickness (3), each supports an axial tensile load of 5 kips. (a) Determine the axial stress in bar (1). (b)If the axial stress in each of the other bars is 6 ksi, what is the dimension, b, of the square bar, and what is the outer diameter, c, of the tubular member? t = 0.2 in. 1 in. (1) (2) (3)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

UPVOTE WILL BE GIVEN. WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. SOLVE IN 2 DECIMAL PLACES. BOX THE FINAL ANSWERS.
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
A thin polymer plate PQR is deformed so that corner Q is displaced downward 1.3 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 64 mm, b = 100 mm, c = 80 mm, and Δ = 1.3 mm.
(A) he figure below shows three metal cubes A, B, C of side 100 mm in direct contact, resting on a rigid base and confined in x-coordinate direction between two rigid end plate. If the upper face of the center cube B is subjected to uniform compressive stress of 0.5 kN/mm², compute for cube B, the following: (i) The direct stress in x-direction (₂) (ii) The direct strains in the three coordinates directions x, y and z (iii) The volumetric strain Rigid A E=150 kN/mm² μ = 0.25 o₂ = 0.5 kN/mm² B E = 200 kN/mm² μ = 0.3 -Rigid C E = 150 kN/mm² μ = 0.25 Rigid
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm mm. 50 mm 340 mm
bb3 please help me this is my last attempt
Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 9- MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2 - F 8 mm 8 mm ↓ 12 mm P
S=25
i need the answer quickly
The bronze bar 3.00 m long with a cross-sectional area of 350 mm is placed between two rigid walls. At a temperature of – 20 °C, there is a gap of 2.20 mm. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use a = 18x10/°C and E = 80 GPa. L = 3.0 m 2.20 mm
Find the Stress if Tensile force 2.3 N applied on rod having cross sectional area of 1 mm2
1. Establish stress equations for both bars in the two-bar assembly shown below which isloaded with force P, and constrained at the two ends, as shown in the figure.