Problem 3 (activity) A regenerative steam turbine has a throttle pressure of 3.8 MPa at 380°C and a condenser at 0.01 MPa. Steam are extracted at the following points: 2.0 MPa, 1.0 MPa, and at 0.2 MPa. For the ideal cycle, find (a) The amount of steam extracted (b) W, Q, and e. (c) For an ideal engine and the same states, compute (d) W, Q, and e and

Problem 3 (activity) A regenerative steam turbine has a throttle pressure of 3.8 MPa at 380°C and a condenser at 0.01 MPa. Steam are extracted at the following points: 2.0 MPa, 1.0 MPa, and at 0.2 MPa. For the ideal cycle, find (a) The amount of steam extracted (b) W, Q, and e. (c) For an ideal engine and the same states, compute (d) W, Q, and e and

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

View Image. Please Write Legibly. Box the final answer. Given: Solution:
3 (a) A simple Rankine cycle uses water as the working fluid (Figure Q3). IA 9 in 4s 4 gout Figure Q3. Rankine Cycle The boiler operates at 7,000 kPa and the condenser at 100 kPa. At the entrance to the turbine, the temperature is 450 °C. The isentropic efficiency of the turbine is 90%, pressure and pump losses are negligible, and the water leaving the condenser is subcooled by 9.6 °C. The boiler is sized for a mass flow rate of 20 kg/s. Determine, (i) The rate at which heat is added in the boiler, (ii) The power required to operate the pumps, (iii) The net power produced by the cycle, (iv) The thermal efficiency. (b) After a long walk in the 14 °C outdoors, a person wearing glasses enters a room at 25°C and 60% relative humidity. (i) What is the difference between specific and relative humidity? (ii) Please explain whether the glasses will become fogged or not and why. An
please provide full calculation
I need help on this assignment: Exhaust gases from the turbine of a simple Brayton cycle are quite hot and may be used for other thermal purposes. One proposed use is generating saturated steam at 110℃ from water at 30℃ in a boiler. This steam will be distributed to several buildings on a university campus for space heating. A Brayton cycle with a pressure ration of 6 is to be used for this purpose. Plot the following:(a) The mechanical power produced,(b) the flow rate of the produced steam,(c) the maximum cycle temperature, all as functions of the rate at which heat is added to the cycle.
Project 2
High-P turbine Low-P turbine Reheater (4) Boiler P4 = P5 = Preheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Find the temperature in degree C at state 4 to 2 deciamal places.
On the diagram below sketch a basic Rankine cycle with superheating. Assume that there are irrevesibilities in the turbine and pump. Identify the device associate with each process. Make sure to label: the states and include important features, e.g. lines of constant temperature, volume, pressure, entropy, vapor dome, etc.
A steam plant works on the Rankine cycle with reheat. Steam enters the turbine at 35 bar, 350°C, and expands to 10 bar, where it passes through a reheater, emerging at 350°C. It then expands to the condenser pressure of 35 kPa. For an ideal cycle, compute (a) workdone in HP and LP turbines (b) heat added in the reheater (c) pump work (d) efficiency (e) heat added in the boiler
3. What are the four major accessories of a Rankine Cycle? Define each.
help on b, c, d please need answers soon
5. Consider a steam power plant operating on the ideal Rankine cycle. The steam enters the turbine at 5 MPa, 350 °C and is condensed in the condenser at a pressure of 15 kPa. Determine the thermal efficiency of the cycle if the steam were superheated to 750 °C. Draw the schematic and Ts diagram.