Problem 3: A car battery has a voltage of ɛ = 12 V. To turn the starter on a car the battery must supply I= 346 A. It takes t = 4.6 s for the engine to start. Part (a) Input an expression for the total charge passed through the starter, Q. Q= Part (b) How much energy did the starter consume, E, in J? E =

Problem 3: A car battery has a voltage of ɛ = 12 V. To turn the starter on a car the battery must supply I= 346 A. It takes t = 4.6 s for the engine to start. Part (a) Input an expression for the total charge passed through the starter, Q. Q= Part (b) How much energy did the starter consume, E, in J? E =

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

3. Suppose that we have 2.10 X 10* doubly charged positive ions per cubic centimeter, all moving north with a speed of 1.40 X 10 m/s. (a) Calculate the current density, in magni- tude and direction. (b) Can you calculate the total current in this ion beam? If not, what additional information is needed?
The graph below shows the current that flows through a device called a diode at different voltages. Instead of the numbers presented on this graph, consider a diode for which current varies with voltage according to the equation I = V11.9. Hint: Plot this equation on your calculator. a. What is the resistance of the diode when a potential difference of 0.59 volts is placed across it? Include units in your answer. b. What is the resistance of the diode when 0.72 volts is placed across it? Include units in your answer.
G7
B A hair dryer is basically a duct of constant diameter in which a few layers of electric resistors are placed. A small fan pulls the air in and forces it through the resistors where it is heated. If the density of air is 1.15 kg/m3 at the inlet and 1.05 kg/m3 at the exit, determine the percent increase in the velocity of air as it flows through the hair dryer 1.05 kg/m³ The increase in velocity is Pin kg/m³ Check my work %6
3. For a Si bar of length 5um, doped n-type at 3x10¹ cm³, calculate the current density for an applied field of 3V across its length. Then do the same for a voltage of 3200V. You can assume that the electron and hole mobilities are 1500 and 500 cm²/V.s, respectively, in the ohmic region below 10¹V/cm and. For higher fields, both electrons and holes have a saturation velocity of 107cm/s.
1. Write the expression for the voltage across the 2 ko resistor, and solve for its value. 9 k2 5kO 9 kO 10 V= 4 kQ 3 k2 2 k.
A 12.0 µF capacitor is charged to a potential of 50.0 V and then discharged through a 175 Qresistor. How long does it take the capacitor to lose half of its charge? Select one: t%3D1.46 ms t = 5.00 ms t%3D0.87ms t%34.36ms None of these is correct Next pag
IMPLEMENTATION OF XOR AND XNOR GATES USING NAND GATES 1. Material Required: Logic Trainer Connecting Wires Components(IC’s): 40112. Procedure:It is clear from the logic diagram that the NAND gate implementation of XOR gate requiresfive NAND gates. You will need two quad- 2 in NAND gate ICs to perform this experiment.Gets the required number of ICs containing NAND gates and other apparatus from the labattendant. Plug in the ICs in the breadboard of the Logic Trainer. Connect 5Vdc power supplyand ground on pins 14 and 7 respectively. For other pin configuration consult the data sheet (wehave already used NAND gates in the first lab so it should not be a problem). Wire your circuitaccording to the logic diagram for XOR gate as given above. Once you have wired the circuit,check it with your instructor and, if approved, power up your circuit. The outputs should beconnected to the LEDs on the Logic Trainer for monitoring purpose. Apply different inputcombinations at the input and note…
1. Calculate the power absorbed by each element. I=5 A P2 + 6 A 12 V + 20 V Pi P3 8V P4 0.21 2. Determine the current i, and the voltages Vy and Vy 90 V i, 10 2 + Vy 20 V Vy40 Q 20 Q
In an experiment you artificially cut in half (-50% reduction) the number of voltage gated sodium channels that are located on the membrane of the axon hillock. 1.) Which of the following is the most likely result of this experimental manipulation? A. Summation of more IPSPS would be required for an action potential to occur B. This change would have no effect on the value required to reach threshold C. Even with a very large number of summating EPSPS it would be impossible for an action potential to occur D. The value to reach threshold would be higher (more positive) making it less likely for an aetion potential to occur E. All of the above statements are FALSE The made-up drug Jeakyhoss degrades myelin resulting in myelin becoming more porous and therefore a poor insulator. 2.) Which of the following would NOT be an effect of leakykose? A. Propagation of the action potential would likely alow B. The action potential may degrade because it can't properly be regenerated C. The action…
Which of the following is a correct statement of Kirchoff’s junction (current) rule for the junction shown below? (a) i1 + i2 + i3 = 0 (b) i1 = i2 + i3 (c) i2 = i1 + i3 (d) i3 − i2 − i3 = 0
Please Answer my question 2 sub parts.... Because I know this team can answer max 3 sub parts... Please answer my question with the parts... Thank u god bless u