Gen 1Gen 3Gen 2Gen 4Bus-Tie6600-V SWBD 16600-V SWBD 2DriveDriveShip ServiceDistributionShip ServiceDistributionMotorMotorPropellerPropellerFIGURE 2.5 ABS-R2 redundancy class of ships with electric propulsion. Problem 2.5: ABS-R2 redundancy class of ship depicted in Figure 2.5 hasthe probability of each side losing power due to failure or planned main-tenance equal to 3% over one year. Determine the probability of the shipgoing dark-having no power at all-over a one-year period.

Problem 2.5: ABS-R2 redundancy class of ship depicted in Figure 2.5 has the probability of each side losing power due to failure or planned main- tenance equal to 3% over one year. Determine the probability of the ship going dark-having no power at all–over a one-year period.

Problem 2.5: ABS-R2 redundancy class of ship depicted in Figure 2.5 has the probability of each side losing power due to failure or planned main- tenance equal to 3% over one year. Determine the probability of the ship going dark-having no power at all–over a one-year period.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Discuss several causes of underwater cable maintenance delays.

Q: The power system shown in Figure Q2.2 experiences a three-phase fault at Bus 5. The fault current at…

A: The system is given asherebase MVA is 100.

Q: Q2. The single-line diagram of a simple three-bi is shown in Figure-2. Each generator is repres-…

A: the single line diagram of a simple three bus power system is shown. Each generator represent by an…

Q: Q1a Voltage control – fault level A load bus (bus-L) is suppling from two different buses A & B via…

Q: b) The single line diagram of a power system is shown in Figure Q2.1 including generator and…

A: Givenlength of line =50 kmMVA base = 100 MVAFor line , base voltage =11 kV

Q: G FOTO 100 MVA 13.8 kV X₁ = 0.15 p.u. X₂ = 0.17 p.u. Xo = 0.05 p.u. AY 100 MVA A:Y 13.8:138 kV X =…

A: Given dataGenerator:Transformer :Line:Transformer :Motor:We need to calculate the value of the phase…

Q: Draw a block diagram of a phase-locked loop (PLL) and briefly explain its operation.

Q: (c) Lightning and switching overvoltages are both important factors to consider when dimensioning…

A: The voltage across electrical components at the time of switching is called switching over voltage.…

Q: Convert the following logic gate circuit into a Boolean expression, writing Boolean sub-expressions…

A: It is given that:

Q: A double-circuit its capacitance to neutral per mile. line is shown below. The conductor radius is…

Q: Crosstalk Glitch Example and Analysis Aggressor Victim Victim Net, V OM Aggressor Net, A Coupling…

Q: A three phase,Y connected, 215 V (line to line), 7.5 kW, 60 Hz, three pole IM has the following…

Concept explainers

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.

Question

Gen 1
Gen 3
Gen 2
Gen 4
Bus-Tie
6600-V SWBD 1
6600-V SWBD 2
Drive
Drive
Ship Service
Distribution
Ship Service
Distribution
Motor
Motor
Propeller
Propeller
FIGURE 2.5 ABS-R2 redundancy class of ships with electric propulsion.

Problem 2.5: ABS-R2 redundancy class of ship depicted in Figure 2.5 has
the probability of each side losing power due to failure or planned main-
tenance equal to 3% over one year. Determine the probability of the ship
going dark-having no power at all-over a one-year period.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

13. _______ current attempts to return to the source over any available conductive path.A. DirectB. AlternatingC. Ground-faultD. Arc-fault
2. (a) (b) (1) A 100 kVA, 4000 V / 200 V, 50 Hz single-phase transformer has 100 secondary turns. Determine: The primary and secondary currents. The number of primary turns. Three single-phase transformers are connected in Delta- Wye (A-Y) as shown in Figure 2.1. Each transformer is rated 100 kVA, 2300/13800 V RMS, 50 Hz. The total three-phase load L is 270 kVA with a power factor of 0.866 lagging. The input voltages are: VAB = 23000° VBC = 2300 Z-120° VCA = 2300 120° Assume that the transformers are ideal and the line-to- neutral voltage on the secondary are in phase with the input voltages. A B C 100000 100000 b n
The reactance data for the power system shown in below figure in per unit ona common base is as the following: X²_x² j0.1 G₁ to j0.25 Ti Select one: O a. No right answer O b.-12.19 pu O c.-14.986 pu O d.-) 3.806 pu 2 j0.3 + AL j0.05 j0.25 Assume that the pre fault voltage at bus 2 = 1 pu. For bolted line (b) to line (c) fault at bus 2, the fault current is = j0.5 3 j0.25 T₂ 4 38 + A j0.25 j0.1 G₂ j0.05
5
10
b) A fault occurs at bus 3 of the network shown in Figure Q4. Pre-fault nodal voltages throughout the network are of 1 p.u. and the impedance of the electric arc is neglected. Sequence impedance parameters of the generator, transmission lines, transformer and load are given in Figure Q4. V₁ = 120° p.u. V₂ = 120° p.u. V₂ = 1/0° p.u. V₂= 120° p.u. jXj0.1 p.u. JX2) 0.1 p.u. jX0j0.15 p.u. jXn-j0.2 p.u. 1 JX(2)-j0.2 p.u. 2 jX)=j0.25 p.u. JX20-10.15 p.u. jXa(z)-j0.2 p.u. 4 jX2(0)=j0.2 p.u. jXT(1) j0.1 p.u. jXT(2)=j0.15 p.u. jXT(0)=j0.1 p.u. Figure Q4. Circuit for problem 4b). = jXj0.1 p.u. j0.1 p.u. - JX(2) JXL(0) 10.1 p.u. = (i) Assuming a balanced excitation, draw the positive, negative and zero sequence Thévenin equivalent circuits as seen from bus 3. (ii) Determine the positive sequence fault current for the case when a three- phase-to-ground fault occurs at bus 3 of the network. (iii) Determine the short-circuit fault current for the case when a one-phase- to-ground fault occurs at bus…
Explain the concept of predictive maintenance in power substations and its potential to reduce maintenance costs and downtime.
A.1. Combination misalignment is caused byA. misalignment by both offset and angle.B. both shafts offset vertically.C. both shafts offset horizontally.D. both shafts being located at an angle.A.2. You can usually check for a leak in a vacuum system by looking at or feelingA. for an air flow along the piping.B. at the exhaust of the vacuum pump.C. at the vacuum gauge at the vacuum pump.D. for signs of dirt on the piping.A.3. When you measure the voltage drop across a set of contacts, you'reA. checking the quality of the contact set.B. sensing how much current is flowing in the circuit.C. measuring the equivalent motor resistance.D. checking the incoming voltages.
Q2 (1). In Figure 2-1, two curves represent fault currents supplied by two sources in case of phase faults at different corresponding locations. Overcurrent protection 1 and 2 are designed to protect line A- B. If there is no directional element, please explain how the setting values for overcurrent protection 1 and 2 could be calculated? (2). If only one directional element is available, please explain how the setting values for overcurrent protection 1 and 2 could be calculated? A B K1 IK1 g K2 Figure 2-1 IK2
The single line diagram of a power system is shown in Figure Q2.1 including generator and transformer winding connection and earthing details. The parameters for this system have been calculated on a common 100 MVA base and are given in Table Q2.1. All resistances and shunt susceptances are neglected. This system experiences a single line to ground fault at a point F on line L1. The point F is at a distance d from Bus 4 along the line L1. The total length ?? of the line L1 is 50 km. Note that the location of ?? is not drawn to scale in Figure Q2.1. The fault current at the fault point F is measured to be 6.106 kA. i) Determine the zero, positive, and negative sequence Thevenin equivalent impedances as seen at the fault point F. These should be evaluated in per unit and shown as a function of d.ii) Use the sequence impedances calculated in part (i) to determine the distance d of the fault (in km) from Bus 4.