Problem 2. 3m 3m 4m Hollow section p1 W b h t 38.0kN 12.1kN / m 164.0mm 264.0mm 7.5mm Determine the maximum bending stress of the following beam shown using the given cross-sectional areas. Prohlem 1 D.

Q: Determine the rectangular representations of the vector F. F-750 N 45 60

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: 7- Describe the flowchart of the experimental mechanistic design along with the relevant steps.

A: A flow chart is a logical arrangement of shapes, lines, and text that visually depicts a procedure…

Q: Solve no 1b the drawing aspect, please solve fast

A:

Q: Question two:A horizontal force of 150 N is needed to pull an 80 kg cart across a horizontal floor…

A: Using work energy principle

Q: If train conventional equipment, consisting of 10 cars, is traveling at 137 km/h on a curve of 2°,…

A: A mode of transport is a system that uses vehicles, infrastructures and operations of a particular…

Q: If Block B travels when it is released from rest to the point that the speed becomes 3m/s. What is…

A: What is the distance created by block B

Q: 2. 3" 3"

A:

Q: submitted Via Zoom Question: Determine the reactions of the structure shown in the Figure. lokN SokN…

A:

Q: This ceiling register has equally spaced openings. a. Find in inches the width of each opening.b.…

A: Total number of opening in a row=9 spacing between the opening in row=38in Total number of opening…

Q: Questic stion What are the advantages and disadvantages of Venturi Meter? Use the editor to format…

A:

Q: My book says the right answer was 90 kPa

A: Given data in question  Unit weight of dry bark clay 18 kN/m3 Saturated unit weight 15 kN/m3 and 21…

Q: Exercise Problem 1: Find coordinates of the Centroid for the following figure:

A: Solution: We need to find the centroid in the given figure. We can divide the figure in 3 parts and…

Q: Define fiber-optic piezometer.

A: A piezometer is a device which is used for measurement of pressure of a fluid in a system or at a…

Q: Using the following notes, what is the elevation of BM,4 Station B.S. F.S HI Elevation BM12 4.64…

A: what is the elevation of BM₁4

Q: Calculate the y-coordinate of the centroid of the shaded area.

A: It is asked to calculate the centroid of the shaded area.

Q: Situation C. Using the figure, supply the data needed in the numbered cell. BS FS 1.27 4.91 BS FS…

A:

Q: A distance between point (A) and (B) is (170m) was measured by a tape of (20m) length, the it was…

A: L=20m

Q: Figure Q1 shows a half view of a light aircraft, with an aileron extending over the outer 50% of the…

A: (a) Consider the free body diagram and support reaction; Calculate the forces in x-direction;…

Q: Determine the moment of inertia of the shaded area with respect to the y-axis. Consider L = 130 mm…

A: If you have any doubts please comment

Q: Figure Q1 shows a half view of a light aircraft, with an aileron extending over the outer 50% of the…

A: The following figure shows the Free Body Diagram of the aileron.

Q: Course: Stress of BO BE CE ARCA = 0.012m² 240 N A 4m 4m 400 N

A:

Q: In fighting with fires, what is the correct way of using a fire extinguisher? A squeeze, aim, sweep,…

A: 1.E Pull, Aim, Squeeze, Sweep

Q: Station 10+50 (elevation = 1103.15') Compute the slope of the line from Station 5+85 to Stat answer…

A:

Q: Question 3 Determine the moment of inertia in Add your answer Question 4 Determine the moment of…

A:

Q: tomm lo tromm Samm Ix = 1.04 * 10^6 Ix = 2.01 * 10^6 Ix = 1.01 * 10^6 Ix = 1.8 * 10^6

A:

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A: Answer We can draw the orthographic projections using the following steps in Autocad 1) Set the…

Q: Civil Engineering Department Answer Sheet Date: Time: P-400 30

A:

Q: . Define "Piping System." 2. What's the difference between a tube and a pipe? 3. Explain the…

A: 1. A piping system is a network of pipes, valves, fittings, and other components used to convey…

Q: Determine centroid Y 40 mm 60 60 mm

A:

Q: Determine 1. Coefficient Uniformity 2. Coefficient of Curvature of the table.

A: Mass retained are noted in laboratory experiment for each sieve. Total mass of soil = 2457…

Q: Briefly discuss GPS applications in Civil Engineering

A: Global positioning system or (GPS) is a navigation facility which is based on sending and receiving…

Q: 14.  From a point on level ground 199 feet from the base of a tower, the angle of elevation of the…

A:

Q: Calculate the correct point A, if the staff re instrument which is s from

A:

Q: Find the coordinates of centroid for the shaded area in fig 1. Hote: All dimensions are in meter.…

A:

Q: An observers watches a plane approach at a speed of 600 mi/hr and at an altitude of 4miles. At what…

A: The values given in the question are as follows: Speed of plane(v)=600 mi/hr Altitude of plane(h)=4…

Q: Q2/ based on table below draw the (histogram) between frequency and classes boundary. Class limit fi…

A:

Q: Completion Status: Welded pin 1200 mm 600- -300 mm mm Figure B1 erical value for the magnitude of M…

A: As math type not available providing hand written solution

Electrical Plans

An electrical plan is also known as an electrical drawing or a wiring diagram. It is a kind of visual representation which bears the blueprint symbols of all the electrical components in electrical house plans or various building construction projects. In other words, electrical plans describe electrical circuits and systems that build up the electrical house plans or building plans. An electrical engineer who works on various construction projects creates an electrical drawing. The engineer outlines the electric planning with different symbols and lines forming a detailed electrical circuit. These drawings are a means of representation for the clients, who will carry out the actual wiring process. In a nutshell, an electrical plan showcases the circuitry with the proper placement of electric components.