Please fast Problem 2: KinematicsConsider a planar 1 DOF ayatem shown below. As-aume all coordinates are zeros when the springs areundeformed. Assume there is no slip between thecord and the cylinder. Let all the pulleys have radiiof R.X23 Find fA written in terms of æ1.(A) A = 21/R(B) 8A = 2x1/ R(C) 8A = 201/3R(D) 8A = 21/3R4. Find og written in terms of æ1-(A) 02 = e1/R(B) 8g = 221/ R(C) 8g = 2x1/3R(D) 02 = 1/3R5. Find ec written in terms of æ1.(A) Oc = 1/R(B) 8c = 21/ R(C) 8c = 2x1/3R(D) 8c = 1/3R

Answered: Image /qna-images/answer/e81863a2-32e2-434a-ba6c-a38d0165c37c.jpg

Problem 2: Kinematics Consider a planar 1 DOF ayatem shown below. As- sume all coordinates are zeros when the springs are undeformed. Assume there is no alip between the cord and the cylinder. Let all the pulleya have radii of R. 3 Find 8A written in terma of æ1. (A) A = 1/R (B) 8A = 2x1/R (C) 8A = 2x1/3R (D) 8A = 21/3R 4. Find 8g written in terms of æ1. (A) ®g = 1/R (B) 8g = 2x1/ R (C) ®g = 2x1/3R (D) ®2 = #1/3R 5. Find 8c written in terms of æ1. (A) @c = 1/R (B) c= 2x1/ R (C) 8c = 2x1/3R (D) ®c = "1/3R

Problem 2: Kinematics Consider a planar 1 DOF ayatem shown below. As- sume all coordinates are zeros when the springs are undeformed. Assume there is no alip between the cord and the cylinder. Let all the pulleya have radii of R. 3 Find 8A written in terma of æ1. (A) A = 1/R (B) 8A = 2x1/R (C) 8A = 2x1/3R (D) 8A = 21/3R 4. Find 8g written in terms of æ1. (A) ®g = 1/R (B) 8g = 2x1/ R (C) ®g = 2x1/3R (D) ®2 = #1/3R 5. Find 8c written in terms of æ1. (A) @c = 1/R (B) c= 2x1/ R (C) 8c = 2x1/3R (D) ®c = "1/3R

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What are the concentrated forces?
Statics of Rigid Bodies Note: If you have already answered the problems in this post, kindly ignore it. If not, then answer it. Thank you, Tutor! Content Covered: - Method of Joints Direction: Create two problems based on the topic "Method of Joints" and then solve them with a complete solution. In return, I will give you a good rating. Thank you so much! Note: Please bear in mind to create two problems based on the topic "Method of Joints." Be careful with the calculations in the problem. Kindly double check the solution and answer if there is a deficiency. And also, box the final answer. Thank you so much!
Which is the simplest type of vibrating motion?
Define the international system of units.
Do you want to see a comparison of the many varieties of dynamic rams in terms of their manufacturing process and physical characteristics?
kinetics of particles-relative motion report
Would the plank and the roller have the same acceleration why or why not?
In the motion of a crank shaft, the piston undergoes rotation rectilinear translation curvilinear translation general plane motion
i need the answer quickly
Q1. The part shown below will be turned in two machining steps. In the first step a length of (50 + 50) = 100 mm will be reduced from Ø100 mm to Ø80 mm and in the second step a length of 50 mm will be reduced from Ø80 mm to Ø60 mm. Calculate the required total machining time T with the following cutting conditions: Cutting speed V=80 m/min, Feed is f=0.8 mm/rev, Depth of cut 3 mm per pass. Ø100 Ø80 Ø60 50 50
4. State Hooke's law.
Define the term Newton's first law of motion