Problem 2:For the differential amplifier circuit shown, v, and y, are pure ac inputs, ignore r and assume b=100.(a) Determine the highest permitted value of the input common-mode voltage (V) assuming the tailcurrent (1-ImA)Q3(b) Calculate the differential gain (v/v) and (v/v), where Vid=V₁-V₂id(c) Find the common mode input resistance (R) considering the output resistance of Q3 (r).VIRe-4kfVelo-SV2₁RBVod+-SVRc-4kf-O Val12

Answered: Image /qna-images/answer/5008afde-d00d-4090-b0c6-1cfd8eef5455.jpg

Problem 2: For the differential amplifier circuit shown, v, and y, are pure ac inputs, ignorer and assume b-100. (a) Determine the highest permitted value of the input common-mode voltage (V) assuming the tail current (1-ImA) CM (b) Calculate the differential gain (v/v) and (v/v), where Vi od id (c) Find the common mode input resistance (R) considering the output resistance of Q3 (r). Vid=V₁-V₂ VI Re-4k- Velo SV 2₁ RB Vod + -SV Re-4k0 01/2 +₁ 12

Problem 2: For the differential amplifier circuit shown, v, and y, are pure ac inputs, ignorer and assume b-100. (a) Determine the highest permitted value of the input common-mode voltage (V) assuming the tail current (1-ImA) CM (b) Calculate the differential gain (v/v) and (v/v), where Vi od id (c) Find the common mode input resistance (R) considering the output resistance of Q3 (r). Vid=V₁-V₂ VI Re-4k- Velo SV 2₁ RB Vod + -SV Re-4k0 01/2 +₁ 12

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the experiment (Differential amplifier) answer the following: Theoretical Calculations: 2. To what type of circuit does a differential amplifier correspond?
Determine the efficiency of the amplifier and discuss the problem of crossover distortion in the amplifier.
d) With the aid of a sketch, describe briefly the definition of the slew rate of an amplifier. Comment on the general principle of selecting an appropriate slew rate of an amplifier in order to avoid causing signal distortion.
c) Sketch a basic differential amplifier circuit and discuss its mode of operation.
Provide a detailed explanation on differential amplifier circuits explain how these circuits work. explain input biasing ,offset current, output offset voltage, common-mode gains,and common-mode rejection-ratio (CMRR). also list possible sources of error that can occur when conducting a differential amplifier circuit experiment.
(b) The multistage amplifier circuit of Figure Q.2(b) have the following parameters: Qı and Q2: B= 200, VBE = 0.7 V, VT = 26 mV , VA=∞ Given that Icọ1 = 2 mA and VCEQ1 = 2 V. (i) Determine the value for R84. List the assumption/approximation made in the analysis. (ii) Sketch and label the small-signal hybrid-t equivalent circuit at midband frequency range. (iii) Calculate the small signal hybrid-n model parameters: gm and ra for Qı and Then, determine Zi2 and Zo. VSI (iv) Find +15 V TU MA RBI 100 k2 UNIVERSITI { Rc 3.3 k2 RB3 10 kN IcQI Q2 C4 Qi VCEQI Ro TEO ► 50 k2 Rs 100 2 RL V. 10k2 RE 2 kN RB4 C3 Zi2 Z, Figure Q.2(b) AYSIA
The input voltage for an Op-Amp series regulator is 12v,, if the non inverting input of the op-Amp is connected to 3 series diodes instead of Zener one . a) Design the the op-amp feedback resistors to give 6.5V fixed o/p voltage b) Determine the line regulation in both % and in %/V. if the input voltage increased by 3V leading to o/p voltage increase of 0.05
1. For the pointer position in the diagram, what is the input signal if the range is set at 0.3 V? A. For the pointer position in the diagram, what is the input signal if the range is set at 1 V? B. For the pointer position in the diagram, what is the input signal if the range is set at 30 V? C. Let’s say you know that the input signal will be about -0.25 V. What range should you select to give maximum deflection without going off scale? Draw a line, with a straight-edge, on the picture above, showing how the pointer would point.
1. By using re model, draw the a.c. equalent circuit for the transistor amplifier shown in figure 1 Figure 1 i. ii. iii. iv. "Î Figure 2 R₁ C₁ V₁ R₂ 2. By using equalent circuit mention in 'part 1'. Write the mathematical expressions for followings, www m input impedence of the amplifier output impedance of the amplifier voltage gain of the amplifier current gain of the amplifier 3. By using h-parameter model, draw the a.c. equalent circuit for the transistor amplifier shown in figure 2. Assume that hre= high (∞), hoe = 0 and the rectance of capacitors C₁, C₂ and C3 is zero. Vcc Rc R₁ C₁ VBE RE R₂ +₁. Vcc Rc RE: C₂ C₂ Vo Vo R₁ R₂ Rc RE hie hfe = 38 ΚΩ = 10 ΚΩ = 4.7 ΚΩ = 2.2 kΩ = 1kΩ = 50
2