Problem 2 Find the equivalent resistance for both circuits below. R11 = 6kN R3 = 2.5kN R4 = 4kN R1 = 10kN Rg = 5kN R2 = 10kN R9 = 7kN R12 = 4kN R7 = 5kN Rg = 1kN %3! R2 = 50 R1 = 10 R3 50 R5 = 90 R6 = 8N R9 = 12 R7 = 2N R, = 1kn R10 = 2kn R4 = 1N Rg = 50

Q: S E Ľ R₁ C1 R3 www R2 R₁ = R₁ C₁ = C₁ C₂ = C C₂ R4 R5 The switch is open and capacitors are…

A:

Q: R4 R2 R3 R12 R6 R5 10 V Rl = 10 n R4 = 100 n R2 = 56 N R5 = 10 n R3 = 10 n R6 = 15 n %3D

A: By using KCL

Q: Find the Norton equivalent current IN that drives R4 when E=14 V, R1=2, R2=12, R3-24 and R4=6. E a…

A: The given circuit diagram is shown below,

Q: PROBLEM 4 Find Req R2 R3 120 R4: 60 R5 R7: 30 60 R1 120: Reg R6 180 Figure 4

A:

Q: In the circuit below, what is the voltage drop across R5 at t=0? Ra R₁ Vo R₂ - C₂ m www Rs L₁ R1-10…

A: We need to find voltage drop across R5 (VR5) for t=o  Circuit:

Q: R3 R, R5 R6 R R7 R4 R3, = R6, = R9 = 50 R2, = R5, = R8 = 42 R1, = R4, = R7 = 20

A:

Q: R2 R9 '3 R, R8 Here R1=11k0, R2=11kQ, R3=2.2kQ, R4=11kQ, R5=11kQ, R6=22KQ, R7=1.1kQ , R8=2.2kQ,…

A: It is given that:

Q: How would you find total Resistance. I found Ra of R7,Rload, and R8 to be 12kOhms. Rb of R6 and Ra…

A: R7, Rload and R8 are series, Ra = 2 + 4 + 6 = 12 kΩRa and R6 parallel, Rb = 12 * 6 / (12 + 6) = 4…

Q: For given value of the circuit, Vsupply = 120 V, and with R₁= 2002, R₂-30.0, R3=75, R4=300, R5=…

A: The required parameter can be calculated by using mesh analysis and ohms law. By using the mesh…

Q: ) What is the equivalent resistance in the circuit below

A: In this question,  We need to calculate the equivalent resistance?  If two resistances R1 and R2 are…

Q: In the given series-parallel circuit, determine the value of current in resistor R4 and voltage…

A:

Q: R3 R2 R1 R5 R4 Rg R6 R7 b

A:

Q: Compute the Norton current IN with respect to the load terminals a-b. Find all solutions…

A: In this question, we need to determine the Norton current IN  across the load terminals a and b.

Q: Determine the current passing thru R2 and R3. And Determine the voltage drop in R4 and R1. * A…

A: First we will find out equivalent resistance then total current then current through each resistor…

Thevenin Theorem

Any linear circuit, no matter how complex, maybe simplified to an equivalent circuit utilizing only a single voltage source and series resistance coupled to a load, according to Thevenin's Theorem. The superposition principle says that all foundational equations must be linear, and the notion of "linear" is still the same (i.e., there should not be any exponentials or roots). This is particularly the case when operating with passive elements like resistors, inductors, and capacitors. However, some components (particularly some gaseous and semiconductor devices like tunnel diode, Schottky diode, transistors like BJT, MOSFET) are nonlinear, meaning their current resistance fluctuates with voltage and current. As a result, circuits made up of these parts are known as nonlinear circuits.