R2 R9 '3 R, R8 Here R1=11k0, R2=11kQ, R3=2.2kQ, R4=11kQ, R5=11kQ, R6=22KQ, R7=1.1kQ , R8=2.2kQ, R9=1.1kQ are the resistances on the circuit where kQ stands for kilo ohm. The electromotive forces of the batteries are E1=8volts and E2=7volt a) Calculate the current through R1. b) Calculate the current through Rbk and call it lbk ? c)Calculate the potential difference across the oc terminal. lo ww

Q: Find 211 mod 95 Answer:

A: Given 21-1 mod 95

Q: Can you please picture the solution again? because it's too vague, I can't read very well. Thank…

A: It is asked to picture the provided solution again.

Q: There are many different matching techniques. What are important factors required to select a…

A: Thre are different matching techniques however they all have certain important factors required to…

Q: Q2) Explain the The difference between power signal and energy signal (with equations) i) i) Unit…

A:

Q: What are the loads that are allowed and are not allowed to connect to a general  socket based on its…

A: Given: General socket question

Q: direct method of measurement is used only when the direct measurement is either impractical or…

A: Correct option is false. direct method of measurement is the measurement in which there will be…

Q: R1 $50 C1 120 Vrms 60 Hz :265.25µF sW Key = A (1 {53.05m H

A: Admittance is the best way to analyze the parallel circuit. Find the admittance of the circuit and…

Q: Determine the source to drain current of the circuit shown below. MYPMOS M1 |=5u w=20u V1 Parameter…

A:

Q: 2) Given the figure and values below: R, = 1000 k, R = 480 kf , RF = 1.2 kfl B, = 60,B; = 120…

A:

Q: I am confused on current drawn by R2, also power dissipated by R2

A:

Q: Series-Parallel Circuit Problem #7 Using the following series-parallel circuit, calculate the total…

A: The required parameters can be calculated by using resistance reduction techniques and also by using…

Q: Example 13: A 230V shunt generator has an armature resistance of 0.0392 and shunt field resistanc of…

A: In this question We need to determine the load current and efficiency of the generator.…

Q: Can you please write the solution in paper or in more comprehensive way? I'm having a hard time to…

A: Given  A vector and we need to convert it into spherical coordinates. Please find the below…

Q: Energy sources that are being traditionally used for many decades are considered as Non-Conventional…

A: This is a basic problem of types of energy sources. The solution is given in the next step

Q: Find Ceq 40 μF 50 μF 30 μF 10 μ 20 μF

A:

Q: Find Ceq 50 μF 40 μF 30 μF 20 μF 10 μF

A: In this question,  Find the equivalent capacitance .  We are solving this problem using the  star to…

Q: There are in general levels of standards of measurements International standards and Working…

A: The solution is given below

Q: A lead wire with a radius of 0.5 mm and a length of 20 cm is connected to a potential difference of…

A: Given diagram,

Q: Can you explain part (b), how did you write the solution

A: It was answered using fourier transform properties.  Property used here is frequency shifting.

Q: Part A In the circuit shown in (Figure 1), find the magnitude of current in the upper branch.…

A: Use nodal analysis to find node voltage.  Using ohms law find current in resistors. Apply KVL in…

Q: 1. What are the values of the resistances bellow according to these colors? a. Orange - blue - green…

A:

Q: If Vcc=9V, Icc(1)=10mA, Icc(0)=30mA. How much will be the power O 180 mW O 360 mW O 360 W O 180 W…

A: Given data, Vcc=9 VIcc1=10 mAIcc2=30 mA

Q: Why TR's are normal sources of DC in large aircraft instead of batteries? O TRis like a battery but…

A: We need to select correct option .

Q: I need the solution for Part B please. 1.07 KiloOhms is incorrect and 0 KiloOhms is also incorrect.

A: Given: Consider the circuit shown in the figure: A Q-point value for IC between a minimum of 4 mA…

Q: need help solving this so i can get an idea of how to do other ones

A: The solution can be achieved as.

Q: If the resistance in a circuit is given by 80 n± 0.2% and the current flowing through it is 5A ±…

A: The solution can be achieved as follows.

Q: Just list, without detailed description. Give at least 5 examples of energy storage systems.

A:

Q: ay you display this in a circuit schematic?

A:

Q: A voltmeter indicates that the value of a voltage crossing a load resistance is 5.00 V, this…

A: Volatge across the load resistance is 5.00V The Voltage can be written as ,

Q: If we were to connect a voltmeter directory to an ohmmeter, what would you expect to see

A: If we were to connect a voltmeter directory to an ohmmeter, what would you expect to see changes in…

Q: In the figure shown below, what is the magnitude and direction of the net Coulomb force vector acted…

A: In the figure,  Total net force on the centre due to circumference charge. If radius r= 100cm.

Q: The current enters to the positive terminal of a device is i(t) = et amps, and the voltage across…

A: Given, Current, it=e-4t A Voltage, vt=3didt               vt=3ddte-4t=-12e-4t V Time, t = 0 to 2 sec

Q: measurements , describe how to read the values given on the measurement tools and to write about…

A: Extension rod- extension rod is used for extensive objects having large diameters, it is used along…

Q: Consider the circuit shown in Figure Q4.1. The switch has been in position A for a long time before…

A: When switch is at position A for a long time , inductor acts like a short circuit .

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.