Problem 2: A piston-cylinder device contains 50 kg of water at 250 kPa and 25 °C. The cross-sectional area of the piston is 0.1 m2. Heat is now transferred to the water, causing part of it to evaporate and expand. When the volume reaches 0.2 m3, the piston reaches a linear spring whose spring constant is 100 kN/m. More heat is transferred to the water LA =0.1 m² until the piston rises 20 cm more. Determine (a) the final pressure and temperature and (b) the work done during this process. Also, show the process on a P-V diagram. A = H2O m = 50 kg wwwwww

Problem 2: A piston-cylinder device contains 50 kg of water at 250 kPa and 25 °C. The cross-sectional area of the piston is 0.1 m2. Heat is now transferred to the water, causing part of it to evaporate and expand. When the volume reaches 0.2 m3, the piston reaches a linear spring whose spring constant is 100 kN/m. More heat is transferred to the water LA =0.1 m² until the piston rises 20 cm more. Determine (a) the final pressure and temperature and (b) the work done during this process. Also, show the process on a P-V diagram. A = H2O m = 50 kg wwwwww

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Block has the potential to produce up to 3000 MWh of geothermal energy when the project is developed to completion. In the region, the average geothermal temperature gradient is 20 °C/km, the maximum depth that can be reached using conventional drilling technology is 10 km, the average annual surface temperature is 25 °C and the rock under the surface in that region has a density of 2600 kg/m3 and a specific heat of 1000 J/kg.K. Determine the minimum mass of rock required to meet this demand.
THERMOFLUID A frictionless piston-cylinder contains 3.30 kg of saturated water at 1 MPa. The water is expanded at constant pressure until its temperature rises to 270 °C. The image of the system and process are shown in Figure 3. Determine: i) the initial volume of water in cylinder ii) the initial temperature of water,
Water, assumed to be a perfect liquid, has a density of 1000 kg/m³ and a specific heat of 4184 J/kgK. The water undergoes an adiabatic, frictionless process in which its pressure is raised from 100 kPa to 1000 kPa. Find the following: (a) the change of specific internal energy (J/kg) (b) the change in temperature (K) (c) the change of specific enthalpy (J/kg) (d) the temperature change (K) required in a non-adiabatic but isobaric process to change the enthalpy the same amount as the change in part c.
Determine the work done by the expanding gas using the trapezoidal rule. from the data in the image
Could you please tell me whether 717.5 J is correct Answer or not (Don't copy ,Incase if you are unsure just skip it . I am confused with value ∆T ) Question 1: Consider a piston–cylinder device that contains 0.5 kg air. Now, heat is transferred to the air at constant pressure and the air temperature increases by 5°C. Determine the expansion work done during this process.
Ammonia with MW=17, weighing 22kg is confirmed inside a cylinder equipped with a piston has initial pressure of 413kPa and 48C. if 2900kJ of heat is added until the final pressure is 413kPa and final temperature is 100C. Determine the change in internal energy kJ
Refrigerant 134a expands in a piston-cylinder assembly from p₁= 200 lb/in² and T₁ = 140°F to p₂ = 30 lb/in² and T₂ = 80 °F. The mass of refrigerant is 0.46 lb. During the process, the work done by the refrigerant is 4.32 Btu. Kinetic and potential energy effects are negligible. Determine the initial volume of the refrigerant, V₁, in ft³, and the heat transfer for the process, in Btu. Step 1 * Your answer is incorrect. Determine the initial volume of the refrigerant, V₁, in ft³. V₁= 0.105743 ft3
answer d
The figure shown above is a 0.5 cm², 5 kg cylinder with a moving piston attached to a spring. The cylinder is filled with unknown gas and initially the spring did not exert any force. Determine the work done when the spring is compressed by 5cm. Assume initial volume is 0.005m³ and k= 100 N/m. Neglect the effect of heat and internal energy.
A ball having 7.62 cm radius contains air (R = 53.3 lbf – ft/lbm - R) at 235.3 psig and 550R. After some of the air was used, the pressure was 200 psia and the temperature was 85ºF. The volume that the used air will cubic inches(nearest tenths). occupy at atmospheric pressure and 80°F is
In a piston-cylinder setup, 2 kg of water undergoes a constant temperature expansion at T=200°C from a volume of V1 = 0.196 m³ to a pressure of p2 = 1 bar . We want to know what the work performed and heat transferred is during this process. If the heat transfer during the expansion process is Q1-2 = 3000 kJ, what is the work done? (Report your answers in kJ)
Propane (MW = 44 ; k = 1.13) initially at 30 psia and 215°F, is stored inside a large spherical vessel having a diameter of 10 ft. If the temperature is increased to 635°F. Determine the following: a. Final pressure in psi b. Mass of propane in Ibm c. Constant Volume Specific heat in BTU/lbm d. Change in Internal Energy, AUU in BTU