Problem #2 A double angle section: 2-L5x32x3 (LLBB) with a separation of " is used as a column with effective lengths (KL), (KL), -22. Assume Fy = 50 ksi. Determine the capacity of the member.

Q: Find the area and put in square feet

A:

Q: Building construction engineering. Carry out the calculations to find the number of actual and…

A: Question is based on construction engineering . Plot size is given in the questionNumber of actual…

Q: Calculate the bearing of a line joining the SW corner of the NE ¼, of the NE ¼ of Section 29 and the…

A: To find the bearing of a line joining the SW corner of the NE ¼, of the NE ¼ of Section 29 and the…

Q: What is DALR line?

A: Lapse rate: The rate at which an atmospheric variable that shows the variation of moist adiabatic…

Q: Define Land Drainage.

A: Drainage is a reverse method of irrigation  This is generally known as the removal / disposal of…

Q: When preparing a written report (which includes survey report, description, and sketch), the shall…

A: ASKED: To choose the correct option corresponding to the given statement.   Given statement: When…

Q: n isosceles triangular lot has an area of 12,640 square feet. The included angle between the two…

A: Median drawn from a vertex divides the opposite sides in two equal parts. Two angles of an isosceles…

Q: (b)       Define Bench Mark. List down its different types

A: A benchmark is a reference point that helps one to calculate something. A "bench mark" associated…

Q: what is the approximate elevation of international Falls above sea level?

A: Answer As per Elevation map of International falls, elevation of International falls ranges from…

Q: 2) Determine the area & perimeter of the trace below. 1300 1000 1600-

A: The length of AB = 130 units The length of CE = 160 units The length of EA = 100 units The area of…

Q: List a few measures that surveyors generally take care of ?

A: Surveying- It is defined as an art of engineering which helps in determining the points relative to…

Q: Describe about the Sliding Block Analysis.

A: The sliding block analysis method used by the Newmark is an engineering which determines permanent…

Q: Excess or deficiency existing in a straight line between fixed monuments within a subdivision is…

A: The given statement implies that even small errors can be distributed equally among original and…

Q: 50 ↓ 50² 50k $50* a M b 6 at 25 ft 150 ft 50k 25 ft PROBLEM: DETERMINE a,b,AND C BY METHOD OF…

A:

Q: Consider the commercial steel pipe shown in (Figure 1). Determine the flow of methane at T = 68°F in…

A: Pressure Drop (ΔP) = 5 * 10^(-3) psiLength of the pipe (L) = 2600 ftDiameter of the pipe (D) = 1…

Q: efine direct evidence

A: Any information that a participant to a lawsuit proposes to show or deny on a specific topic in a…

Q: Define the assumptions of Boussinesq Equtions?

A: This equation is to predict the amount of stress over the material. It predicted the stresses in an…

Q: Determine the length of the dividing line which will divide the lot into two equal areas which is…

A:

Q: define the Urban Design

A: We need to define "urban design".

Q: In a typical township what sections are in the four corners?

A: Township - It is referred as various kinds of settlements or administrative sub-divisions in urban…

Q: What is over-consolidated?

A: There are 3 types of consolidation stages namely : 1- over consolidation stage 2- normal…

Q: 2. £{est}

A: Given  L{e5t}

Q: A triangular lot ABC has a bearing and distance of line AB to be N 40deg E and 800m and CA equal to…

A:

Q: Define Reinforced Earth.

A: The reinforced earth is defined as “the composite material formed by the soil with low bearing…

Q: Define Soil conditions.

A: Soil condition:

Q: What are orignal documents?

A: Original documents are the cover term used to explain the master copy of legal papers. Most of the…

Q: Define island bar.

A: Island bar:

Q: Define Earth surcharge loads

A: Surcharge can simply be defined as additional or in extra.

Q: How many separate fields should be included in a single RFI, and what are their purposes

A: This question is related to the Building design and drawing from civil engineering.

Q: PROBLEM 4 THE ROOF ON THE BUILDING IN FIG. P1.1 HAS A SLAB THAT IS 175 MM. THICK. THE BEAMS ARE 300…

A:

Q: Define Settlement loads

A: A settlement is the ground's downward movement whenever a load applied to it.

Q: Define COMPRESSIBILITY AND SETTLEMENT

A: Compressibility- It is defined as the change in volume of soil due to the application of mechanical…

Q: What is the difference between territory and personal space?

A: Difference between Peronal space and territory space:

Q: What types of conduit are in general use?

A: Types of conduit that are generally used are Rigid Metal Conduit—RMC and IMC. Electrical Metallic…

Q: Define Footing WidthThe

A: Footing is a structure made of brick, stone, or concrete under a wall foundation or column to…

Q: how many hallow blocks in one storey house?

A: Number of bricks depend upon area of building and height of building in the question Both are not…

Q: 2. ) Compute area of the parcel below. <-5.0 -19,7 0,0 -15,0 0,0 15.0 -4.6 17,0 --3,2 18,4

A: The given figure is shown below:

Q: abel an earth dam

A: The successive layers of earth when piled together to form core and the upstream and downstream…

Q: Explain the coordinate method for the partitioning of lands?

A: Land partition is a common activity for surveyors as well as engineers while conducting property…

Q: Road survey including plan , L section & X-section

A: Road Survey : Road survey is the process to know the properties of the site to where new highway is…

Q: The parents want to subdivide their inner lot into two equal area for their two sons such that the…

A: Surveying is the major measuring branch of civil and for designing the proper planning and leveling…

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.