Problem 12: Determine the magnitudes of the forces C and T, which, along with the other threeforces shown, act on the bridge-truss joint.3kN16 kN408 kN

Answered: Problem 12: Determine the magnitudes of…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The truss is loaded as shown. 6.8 ft 3.9 ft 8 ft V650 lb Analyze it using the method of joints to find all member forces and reactions in pounds. (Assume that the +x-axis is to the right and the +y-axis is up along the page. АВ magnitude Ib sense compression FAC magnitude Ib sense compression ВС magnitude Ib sense tension magnitude Ib direction B. magnitude Ib direction By magnitude Ib direction
Find 5 internal Forces of the truss members also Find all Zero Member forces. 50KN SOKN 0.8m সব সময় 1.5m 100 KN 60m
Q.6. A cantilever truss carries a concentrated load P as shown in the figure below: A (111) e=tan (3/4) (11) B P What are the magnitudes of axial forces in the members 1, IT and 111, respectively? a) 1.00P, 1.33 P and 1.67 P b) 1.67P, 1-33 P and 1.00P c) 1.33 P, 0.75P and 0.60 P d) 0.60 P. 0.75P and 1.00 P
Determine the resultant R of the Four forces acting on the simple truss. The Fourth force is acting on the node where the 25 KN is at and is directed upward with a magnitude of 15 KN. Specify the points on the x- and y-axes through which R must pass. 30° 20 kN 25 kN y 5 m 3 m 6 m 3 m ---x 30 kN
The bridge is constructed as a three-hinged trussedarch. Determine the horizontal and vertical components ofreaction at the hinges (pins) at A, B, and C. The dashedmember DE is intended to carry no force.
Problem 5. The frame shown is hinged to rigid supports at A and E. Find the components of the hinge forces A and E and the forces in members BC and BD. E A 2m 2.5m 12 kN D 2m 1.5m B 2m
Compute the bar forces in all member of the truss shown:
Determine the forces in all members of the truss shown in figure. Assume all members are pin connected.
Kindly write the full solution on a piece of paper rounded off to 4 decimal places, much appreciated
A sign is subjected to a wind loading that exerts horizontal forces of 300 lb on joints B and C of one of the side supporting trusses. Determine the force in members BC, CD, DB, and DE of the truss and state whether the members are in tension or compression.
Determine (approximately) the force in each member of the truss. Assume that the diagonals CAN support compressive or tensile force.

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Problem 12: Determine the magnitudes of the forces C and T, which, along with the other three forces shown, act on the bridge-truss joint. 3kN 16 kN 40 8 kN