Problem (10) A 5-m beam AE is being lowered by means of two overhead cranes. At the instant shown it is known that the B D velocity of point D is 1 m/s downward and the velocity of point E is 1.5 m/s downward. Determine - 1.5 m - 2 m -1.5 m a) the location of point of zero velocity on the beam. b) the velocity of point A

Problem (10) A 5-m beam AE is being lowered by means of two overhead cranes. At the instant shown it is known that the B D velocity of point D is 1 m/s downward and the velocity of point E is 1.5 m/s downward. Determine - 1.5 m - 2 m -1.5 m a) the location of point of zero velocity on the beam. b) the velocity of point A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When the flywheel rotates 20 revolutions, it achieves an angular velocity of wf = 30 rad/s, starting from initial velocity of wo = 5 rad/s. Determine; a) the constant angular acceleration. b) the time required to complete 20 revolutions.
Load B is connected to the double pulley by one of the two unstretched cables as shown. The movement of the pulley is controlled by the cable C, and the cable C has a constant acceleration of 225 mm/s2 and an initial velocity of 300 mm/s2. And both directions are to the right. (a) Number of revolutions by the pulley in 2 seconds (b) Change in speed and position of load B after 2 seconds (C) Find the acceleration at point D when t=0.
D Answer: АГО C 40 mm 160 mm B Knowing that crank AB rotates about point A with a constant angular velocity of 910rpm clockwise, determine the magnitude of the velocity of the piston (m/s) when
If the angular velocity of the side A0 is (rad / s 4) clockwise. At the moment shown in the figure, find the following: a) the magnitude of the angular velocity of the side CD b) the magnitude of the angular velocity of the triangle OBD (rad/s) c) the magnitude of the velocity and its direction to point E D ) Then the direction velocity at point E with respect to + ve x - axis (degreo)
The dimensions of the various links of a mechanism, as shown in Fig. 7.36, are as follows : AB = 30 mm ; BC = 80 mm ; CD = 45 mm ; and CE = 120 mm. B. 30° 75 mm 22.5 mm E Fig. 7.36 The crank A B rotates uniformly in the clockwise direction at 120 r.p.m. Draw the velocity diagram for the given configuration of the mechanism and determine the velocity of the slider E and angular velocities of the links BC, CD and CE. Also draw a diagram showing the extreme top and bottom positions of the crank DC and the corre- sponding configurations of the mechanism. Find the length of each of the strokes. [Ans. 120 mm/s ; 2.8 rad/s ; 5.8 rad/s; 2 rad/s ; 10 mm; 23 mm]
15.9 A 0.6-m radius drum carrying the load A is rigidly attached to a 0.9-m pulley carrying the load B as shown. At the time t=0, the load B moves with velocity of 2 m/s downward and a constant acceleration of 3 m/s2 downward. Over the time, 0 is less than or equal to t and 2 is greater than or equal to t, s determine (a) the number of revolutions executed by the pulley displacement of the load A.
30° 90° E 560 mm PROBLEM 15.69 An automobile travels to the right at a constant speed of 80 km/h. If the diameter of the wheel is 560 mm, determine the velocities of points B, C, D, and E on the rim of the wheel.
15.28 In the position shown, the crank AB rotates with wAB= 10 rad/s counterclockwise. Suppose B' is the point CD coinciding with the pin at B. (a) Is the component of vB of the pin at B in the direction perpindicular to the slot equal to vB'? (b) Determine vD at the point D.
2. How far from the axis of A will the center of the roller R be located if the angular speed of shaft B is three times as that of A? A B 20.5cm
THIS IS A SUPPLEMENTAL STUDY PROBLEM GIVEN AS AN EXTRA EXAMPLETHIS IS NOT A GRADED ASSIGNMENT
If the angular velocity of the side AO is 5rad / s clockwise. For the moment shown in the figure, find the following: 1) the magnitude of the angular velocity. For side CD 2) is the magnitude of the angular velocity of the triangle OBD. 3) The magnitude and direction of the velocity of point F.
b) A peg P is driven by the fork link along the curved path shown. Sketch the polar unit vectors, û, and ûg, and the normal-tangential unit vectors, ûn and û,