NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The bent pipe shown rotates at the constant rate ₁-10 rad/s. It is known that a ball bearing D moves in portion BC of t pipe toward end Cat a constant relative speed u=2 ft/s. Z 12 in. 5 in. D 6 in. Determine, at the instant shown, the velocity of D. (You must provide an answer before moving to the next part.) 1.6 ft/s)i + ( 8.5 ft/s)j + ( The velocity of Dis vp=( 8.8 ft/s)k.

NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The bent pipe shown rotates at the constant rate ₁-10 rad/s. It is known that a ball bearing D moves in portion BC of t pipe toward end Cat a constant relative speed u=2 ft/s. Z 12 in. 5 in. D 6 in. Determine, at the instant shown, the velocity of D. (You must provide an answer before moving to the next part.) 1.6 ft/s)i + ( 8.5 ft/s)j + ( The velocity of Dis vp=( 8.8 ft/s)k.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the instant shown 0 = 45 deg and w = 9.2 rad/s. Link AB is currently vertical. First calculate the speed of point A in m/s if the length of Link OA is 5.2 m and the length of Link AB is 7.35. (The block at B is a slider that can only slide vertically up and down) Answer: 47.84 Next, calculate the i component of the velocity of A. Answer: Check W Next, calculate the component of the velocity of A. Answer: Check
When block B is resting on the surface, pulley A is rotating at a constant angular acceleration α = 6 rad/s². Pulley C has an inner hub D which are turning together as one body. Assuming the belt is inextensible and does not slip What is the speed of block B, in m/s, when it is at 6 m above the surface? Round the answer to two decimals. 50 mm A 75 mm 150 mm C B
6. A ball is rotating about the origin with a constant radius of 10cm. a. For the values of 0, 0, and O shown on the figure, what are the radial (a,) and theta (a) components of the acceleration of the ball. b. What is the acceleration vector of the ball expressed in rectangular coordinates, in terms of i and j unit vectors? Y r = 10cm 10 = -40° X 0 = 4 rad/s Ö = 6 rad/s²
Question 2: The applied force P causes block B to accelerate at ab = 5 Xb 0.25x ft/s², where x, is the position of block B measured from fixed point D. Initially, x, = 0.5 ft and the blocks are at rest. When x = 3 ft, find: a) The velocity and acceleration of B relative to A b) The absolute velocity of point C on the cable CA D- For each answer, report whether the direction is to the right or the left. -
● A 5 rad/s .2 rad/s² 3 ft X 3 rad/s -2 rad/s² B 2 ft 30⁰ с The robotic arm shown above has a fixed orange base at A and fixed length members AB and BC. Motors at A and B allow for rotational motion at the joints. Based on the angular velocities and accelerations shown at each joint (described with respect to the fixed frame): o Determine the velocity at the end effector at C o Determine the acceleration at the end effector at C
5. Two cars are traveling around a circular track as shown below. Answer the following questions. a. Use the drawing provided to clearly indicate the origin and direction of û, and ûn for each car. a. b. If both cars are traveling at the same speed, which car has a greater normal acceleration? Justify your response in words. C. If both cars travel at 50 mph, what is their velocity in ft/s? Show your work. Magnitude rounded to 3 sig. fig. Magnitude rounded to 3 sig. fig. Units 6. At the instant shown below, the bucket of the backhoe traces a path defined by r = 25 sin 0 ft, where 8 is in radians. When the bucket is at 0 = 100°, its angular velocity is 1.8 rad/s and its angular acceleration is Ö = -0.4 rad/s2. Answer the following questions. What is the radius, r, at this instant? Show your work. Magnitude rounded to 3 sig. fig. Units b. What is ve at this instant? Show your work. Units 7-400 ft = fe= 390 ft B
Urgent please solve
Please include explantion. Gear A is between a stationary gear rack F and the gear rack E, which is moving at vE=8 ft/s to the right at the instant shown. It is also observed that the acceleration of gear A is 2 ft/s2 also to the right. At this same instant, determine the angular velocity and angular acceleration of disk B. Use RMA for velocity analysis.
2. A truck's speed increased uniformly from 20 km/hr to 70 km/hr in 30 sec. determine (a) the average speed (b) the acceleration and (C) the distance traveld.
Dynamic
In the position shown, collar B moves to the left with a constant velocity of 360 mm/s. Determine the velocity of collar A. The velocity of collar A is mm/s. → ? Note: Please consider everything. Refer to the image for more clarity. On occasions I receive wrong answers!!. Kindly, please show step by step working out!. And double check the final answers and the force of the units for correction purposes. Appreciate your time!
car A round with curve 150m radius with constant velocity 20m/s. at instant car B moving with a velocity of 30m/s and slows down 5m/s^2. find magnitude of velocity as well as acceleration of car B observed from A (Vb/a and aB/A) please show clear work