Problem 1.9-3 A horizontal beam AB with cross-sectional dimensions(b-0.75 in.) X (h-8.0 in.) is supported by an inclined strut CD andcarries a load P- 2700 lb at joint B Isee figure part (a)l. The strut,which consists of two bars each of thickness 5h/8, is connected to thebeam by a bolt passing through the three bars meeting at joint C[see figure part (b).-4R--5 t-OB3 t(a) If the allowable shear stress in the bolt is 13,000 psi, what is theminimum required diameter dain of the bolt at C?(b) If the allowable bearing stress in the bolt is 19,000 psi, what isthe minimum required diameter d of the bolt at C?D.(a)Beam AB (b × h)Bolt (din)SbStrut CD(b)

b=0.75 in h = 8 in the load carried by the truss at joint B (P) =2700 lb the thickness of each bar =…

Problem 1.9-3 A horizontal beam AB with cross-sectional dimensions (b-0.75 in.) X (h-8.0 in.) is supported by an inclined strut CD and carries a load P-2700 lb at joint B [see figure part (a)]. The strut, which consists of two bars each of thickness 5b/8, is connected to the beam by a bolt passing through the three bars meeting at joint C Isee figure part (b)J. (a) If the allowable shear stress in the bolt is 13,000 psi, what is the minimum required diameter dein of the bolt at C? (b) If the allowable bearing stress in the bolt is 19,000 psi, what is the minimum required diameter d of the bolt at C? 5 ft 3 ft D.

Problem 1.9-3 A horizontal beam AB with cross-sectional dimensions (b-0.75 in.) X (h-8.0 in.) is supported by an inclined strut CD and carries a load P-2700 lb at joint B [see figure part (a)]. The strut, which consists of two bars each of thickness 5b/8, is connected to the beam by a bolt passing through the three bars meeting at joint C Isee figure part (b)J. (a) If the allowable shear stress in the bolt is 13,000 psi, what is the minimum required diameter dein of the bolt at C? (b) If the allowable bearing stress in the bolt is 19,000 psi, what is the minimum required diameter d of the bolt at C? 5 ft 3 ft D.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve this question queckly
kindly answer this step by step, thank you
5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
0.9D+1.3W (When considering the wind load during construction) Calculation of required strength for axial force, shear force and bending moment of AB, BC, and DE members in 3 hinged frame Factored Load Application status
The answer is between 18.25 and 20.25
An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total uniform load of 45 kN/m all throughout its length. STEEL DECIGON CIVIL ENGINEERING Beam properties: A= 11,500 mm² bf = 250 mm tw- 10 mm d === 350 mm If=: 16 mm 1x = 266 x 106 mm c) To strengthen the beam, 2- 200 mm x 10 mm cover plates, one at the top of the flange and the other at the bottom of the flange were added. What is the resulting maximum bending stress?
span of beam af is 6 meters. Thank you.
Please solve question c
The floor system shown below supports a uniform dead load of 100 lb/ft² and a uniform live load of 40 lb/ft?. Draw the loads with magnitudes on the following structural members: а) BI b) В2 с) ВЗ d) B4 e) Gl f) G2 g) G4 6 @ 7' = 42' C4 G1 B3 B2 2 @ 15' = 30' G4 G3 G2 BT 5 @ 6' = 30' 42' 36' For the same floor plan shown above and assuming the same floor loads and that the building consists of four floors, determine the following: a) The dead load on column Cl in the first floor. b) The live load on column C2 in the second floor. Consider live load reduction. c) The sum of the dead plus live loads on column C3 in the third floor. Consider live load reduction. OT
The floor structural system shown in Fig 1 comprise W-section steel beams and girders supporting a 5-inch thick concrete slab which provides full restraint to the flanges of the beams. The density of concrete is 150 lbs. /ft³. and the uniformly distributed live load L=50 lbs/ft². L-22¹ B B. Girder G1: - [82] 12' Gl GI [BI] FIG. 1-Steel Floor Beam a) Strength - Bending and Shear 12' + I 1) Produce a sketch of the floor plan showing the tributary load distribution areas for the beams and girders [zul
PLEASE HELP MEEE