Problem 1. (15pts) The specific gravity of an unknown fluid is 0.85. Given a mass of 1kg of the unknownfluid, determine the following:a) the density of the unknown fluid in [kg/m³]b) the volume of the fluid in [L]c) the specific weight of the unknown fluid in [kN/m³]

The objective of the question is to determine the density, volume, and specific weight of an unknown…

Answered: Problem 1. (15pts) The specific gravity…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The viscosity of a certain fluid is 2 x 104 poise. Determine its viscosity in both (a) Sl and (b) BG units. (a) (b) N*s/m² lb*s/ft²
As shown in Figure 1, an ideal gas flows isentropically from a large tank into a converging nozzle and exits to a receiver. The gauge pressure of the ideal gas in the large tank is 80 kPa. The nozzle exit area is 38 cm?. (Assume Pam = 101 kPa). a) Determine Mach Number at section 1, the EXIT mass flow rate and EXIT Mach mumber. b) Calculate the flow area at section 1. V: = 580 km/hr T:= 500 K Exit, A Large Tank P= 166 kPa (abs) Ideal Gas k=1.43 R= 0.2968 kJ/kg.k Vi = 480 kan/hr Figure 1
1. The reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. The tank is A deep and is contaminated with B of water. The specific volume of gasoline is 0.00147076 m /kg and that of air is 0.0008313 m³/kg. Unit weight of water is 9790 N/m3 a. Determine the gage reading when the tank is full of gasoline b. How many cm of air remains at the top when the gage indicates full if the tank is A deep and is contaminated with B of water. c. Determine the pressure at the interface of the gasoline and water when the gage indicates full A = First name in inches Vent B = A/10 in inches Air h A Gasoline Pgage Water B
Gauge pressure-
A two-dimensional flow field for a liquid is defined by V[(z+2y³)i + (2x-3y)j m/s, where z and y are in meters Part A Determine the magnitude of the velocity of a particle located at (-2 m, 1.2 m) Express your answer to three significant figures and include the appropriate units. V= Submit Part B Request Answer Determine the direction of the velocity of a particle located at (-2 m. 1.2 m). Measure the angle counterclockwise from the positive z axis. Express your answer in degrees to three significant figures. 0- Submit Request Answer
b) i. Explain how to determine the fluid properties of these liquids in the laboratory by applying Archimedes' Principle. ii. Justify three (3) important applications of the principle. Given Table Q1(b), the specific gravity of Liquid A and B. (C4) Table Q1(b) Liquid Specific gravity, SG 0.825 A B. 0.934
For part B) need good explanation.
Q2: A pressure gage 19.0 ft above the bottom of a tank containing a liquid reads 13.19 psi,another gage at height 14 .0 ft reads 15.12 psi. The density of * :the liquid is 1. 73 slug/ft O 3.10 slug/ft O 0.0216 slug/ft O 4.83 slug/ft O
Q3: A U-tube containing mercury is used to measure the pressure of an oil of specific gravity 0.82 as in figure 2. Determine (1) Calculate the pressure of the oil, if the difference of mercury level be 400mm What was the application of pascal's law and hydrostatic law for this problem? (ii) ¼ 300 mm Water Water -oil Figure 2 200 mm. 400 mm 400 mm -X -Mercury
A tank contains gasoline and glycerine with open piezometer tubes attached as shown. The depths of fluids inside the tank are 2 m for air, 1.5 m for gasoline, 1 m for glycerine. The air pressure measured by the gage is 1.5 kPa. Unit weights are 6670 N/m3 for gasoline and 12360 N/m3 for glycerine. Air Gasoline Glycerine 6.0 Find the height of gasoline in the tube measured from the gasoline-glycerine interface. a.) 1.72 m b.) 1.22 m c.) 0.22 m d.) 2.72 m 7.0 Find the height of glycerine in the tube measured from the air-gasoline interface. a.) 0.93 m b.) 0.43 m c.) 0.57 m d.) 1.93 m e.)
The pressure drop in a system is dependent on the ff quantities: fluid velocity, fluid density, pipe diameter, and throat diameter. How many dimensionless can be formed
Name: . Class Q-3 Three different liquids with properties as indicated fill the tank and manometer tubes as shown in Fig. Determine the specific gravity of Fluid 3. Fluid 1: specific weight = 62.4 Ib/ft Fluid 2: density = 1.60 slugs/ft Fluid 3: specific gravity = ? Fluid 2 7 ft Fluid 1 Fluid 3 6 ft 5 ft 3 ft

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Problem 1. (15pts) The specific gravity of an unknown fluid is 0.85. Given a mass of 1kg of the unknown fluid, determine the following: a) the density of the unknown fluid in [kg/m³] b) the volume of the fluid in [L] c) the specific weight of the unknown fluid in [kN/m³]