Problem 1 W MB k 4 m 2 m The cantilever beam above is made up of concrete with E = 70 MPa, refer to the table below for the properties and loads for the beam: PROPERTIES LOADS b (mm) h (mm) w (kN/m) Mb (kN-m) 300 500 20 40 Using area moment method, determine the following: If a concentrated load will be placed at B to remove the deflection at C, determine the magnitude of this load in kN. A 2° B *

Problem 1 W MB k 4 m 2 m The cantilever beam above is made up of concrete with E = 70 MPa, refer to the table below for the properties and loads for the beam: PROPERTIES LOADS b (mm) h (mm) w (kN/m) Mb (kN-m) 300 500 20 40 Using area moment method, determine the following: If a concentrated load will be placed at B to remove the deflection at C, determine the magnitude of this load in kN. A 2° B *

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

Wed 20 Apr 45% Stresses in Beams part 5 thi qar (5 of 6) Second Class Lecturer: Dr. Ali Al Asadi Example 3: The beam shown below has a cross section of channel shape with width b=300 mm and height h=80 mm, the web thickness is t=12 mm. Determine the maximum tensile and compressive stresses in the beam due to uniform load. 300mm 3.2 KN / m 80 mm -12 mm 3 m 1.5 m 14.4 KN EM, =0 B,x3-14.4x2.25=0 B=10.8 KN B F = 0 A A,+10.8-14.4=0
Note: please use set B data W 2° Me A B C * 4 m 2 m The cantilever beam above is made up of concrete with E= 70 MPa, refer to the table below for the properties and loads for the beam: PROPERTIES LOADS SET h (mm) w (kN/m) Mb (kN-m) b (mm) 300 500 20 40 A (1,3,5,7,9) 400 15 45 B (2,4,6,8,0) 250 Using area moment method, determine the following: Moment reaction at A. MA
Help me how to design the REINFORCED CONCRETE BEAMS WITH IRREGULAR CROSS SECTION as shown infigure 1 using the following parameters:F’c = 3,500 Psi Fy=Grade 40 Stirrups = Φ10mmMu = 200 Kn-M All Concrete cover = 30mm Es=200,000 Mpa Find the following: AC area of compression concrete stress block in mm. Assume z = 0.85dEff a height of compression concrete stress block in mm. c distance from the neutral axis to outermost compression fiber in mm. z actual moment arm for Mu=ØTz in mm. As actual area of tension steel in sq.mm. N quantity of Ø20mm steel rebars ЄS Actual Strain of steel ЄY Yield Strain of steel Check if the beam is singly reinforced concrete in the designed then concludeCheck: ЄY < = > ЄS Draw the Working Drawings of the x-section.
Q-2: Estimate short-term and long-term deflections for simply supported beam shown in Figure below, which is assumed to be made of nominal aggregates and properties removed at twenty-eight day. Concrete grade: C30 Instantaneous static modulus of elasticity 26 kN/mm Reinforced: hot-rolled high-yieldf, Loading: dead (permanent = 460 kN/mm? = 10 kN/m u.d.l = 5 kN/m u.d.l %3D Live (transitory) ba 300 2 No 12mm bars span=12m AS 5 No 25 mm bars 009 =P
C (b/h) 8ød b/2 b/2 The geometry and reinforcement configuration of the column is given below. The material properties are CX/S420. The analysis results due to different loading combinations are as follows (C30,b=400mm,h%3D600mm) Combo 1: Nd%3D1250 kN / Mdx = 250 kN Combo 2: Nd%3D1000 kN / Mdx = 400 kN Combo 2: Nd%3D750 kN / Mdx = 550 kN Determine the longitudinal reinforcement of the column.
Determine the load capacity of the angle ASD. USE NSCP 2015.
a reinforced concrete beam is designed to reach fc= 12 MPa and fs= 140 MPa simultaneously. if n=6 and d=450, compute for "jd". Note As (area of steel) is not given. cosidering cracked analysis a.none b. 380.769mm c. 388.983mm d. 399.057mm e. 393.750mm f. 384.677mm
Compute the long-term deflection of the beam at midspan if it is constructed for almost 12 months under a service load (15kN/m for dead load and 10 kN/m for live load) as shown in the figure if the compressive strength of concrete is 28MPA and the yield strength of the steel reinforcement is 414MPa. (mm) 300 mm Pu = 30 kN Wu = 25 kN/m 6m 4-25mm
i need clear ans and solve very very fast in 20 min and thank you DYBALA .: For the composite structure shown in Figure, using unit load method (virtual work method), find the vertical deflection at B ( AVB), use El=100,000 kN.m2, AE 10,000 kN. A 10 kN/m AAAAAAA 6m B 6m D Link 3m C
A simply supported beam has a height of 600 mm and a width of 300mm. Determine the maximum safe live load that the beam can carry. The dead load is the beam weight plus a superimposed load of 15 kN/m The stirrup size is 12 mm, the top bars are 2-20 mm and the bottom bars are 5-28 mm. The clear distance between layers of bottom bars is the bar size, 28 mm. Use fc'=30 MPa, Grade 60 (fy=414 MPa) reinforcements and concrete cover of 50 mm.
Fill in the blanks: Determine the required tension steel area of the T beam with given properties below. Width of flange bf= 500 mm Width of web bw = 400mm Thickness of flange tf 140 mm Effective depth d = 380 mm Effective concrete covering d' = 75 mm Compressive strength of concrete fc' = 30 MPa Yield stress of steel bar fy = 300 MPa Mu = 448 kN-m As = mm2 CS Scanned with CamScanner
4) Compute the shear force (VRDC) for the beam. Check if beam needs shear rebar. Given Cross Shear force obtained in critical section, VED-35 kN Assume 1.5 for K value Rebar: 4012 in tension Material properties: fck-25 MPa (concrete). fyk-420 MPa (steel) Effective height, d=560 mm Material reduction factors: 1.5 for concrete, 1.15 for steel section dimension: b-300 mm, h=600 mm section 000 Twitte