Problem 1) The space truss below has a force F = {−200î + 400ĵ + 0k}N acting at joint D. Find all the support reactions and forces in all members. For each member, state whether it is in tension or compression.

Q: I need parts 8, 9, and 10 answered. Number 1 is an example of how it should be answered. NOTE: Read…

A: (8) Four 0.562” diameter of drill (through holes), each with 0.625” counter bore diameter with spot…

Q: Which of the following statements is not true? Select one: O a. Reports can contain bulleted or…

A: As we know Equations should be written in a symmetric manner, not just in the left margin. Equation…

Q: Draw the top view  front view  right side view  on graphing paper please. Put measurents if…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Which of the following are not used for creativity enhancement? TRIZ Questioning assumptions The…

A: The given options are : TRIZ Method Kung-Lo Method Six Thinking Hats

Q: Are you able to show an answer in terms of using formula from start to finish to get the answer…

A: Are you able to show an answer in terms of using formula from start to finish to get the answer…

Q: A particle P of mass m = 3 kg arrives at point O with a horizontal velocity and starts rolling down…

A: Given:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: where did you get 0.157

A: Given:Figure with dimension is providedTo find:Percent reductions in areaPercent reduction in area…

Q: can tutor continue the next two questions also

A:

Q: please help solve A-F. thank you You are an engineer working on a project and your prototype has…

A: LOAD DEFLECTION (LB) (IN) 0 2 3000 2.00167 6000 2.00333 7500 2.00417 9000 2.009 10500 2.04 12000…

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A:

Q: can tutor explain the what is all of the equations means and also answer the next 2 questions

A: To solve the physics problems, let's break them down one by one:1) Calculate the force experienced…

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: The question is not answer fully. Please answer the second part of the question statement.

A:

Q: can tutor explain the questions more detailed

A: Weight on the wing, W = 80 KNLift force on the wing, F = 100 kNThe cross-sectional area of the wing,…

Q: What type of scale is 1:1? Full Scale O Enlargment Scale Reduction Scale

A: Scale factor is the ratio of the length of the drawing to the actual length of the object. The scale…

Q: You are tasked to check the safety factors for the bolt designs for the connection shown with an…

A: Find outSafety Factor for the Bolt DesignCalculate the required torque to bring the bolts to the…

Q: I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps…

A: Answer to question no. 1Yes, the print shows the detail drawing of a single part here. The drawing…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.