Problem 1: HD-based Ch 7 & MSH-based Ch 3: a solution of unknown origin. Based on the shear rate and shear stress characteristics, determine the type of fluid. A) Mark your answer by placing the Capital Letter corresponding to the correct term in the box. B) What is the viscosity of the solution when the shear stress is sufficient for movement? Remember units. Answers must be supported by an appropriately labeled and hand drawn graph (practice for exams). The following data was obtained for

Problem 1: HD-based Ch 7 & MSH-based Ch 3: a solution of unknown origin. Based on the shear rate and shear stress characteristics, determine the type of fluid. A) Mark your answer by placing the Capital Letter corresponding to the correct term in the box. B) What is the viscosity of the solution when the shear stress is sufficient for movement? Remember units. Answers must be supported by an appropriately labeled and hand drawn graph (practice for exams). The following data was obtained for

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 7 A model tow-tank test is conducted on a bare hull model at the model design speed in calm water. Determine the effective horsepower (hp) for the ship, including appendage and air resistances. The following parameters apply to the ship and model: Ship 1,100 Model Length (ft) Hull Wetted Surface Area (ft2) Speed (knots) 30 250,000 15 Freshwater Water Seawater 50°F 70°F Projected Transverse Area (ft²) Cair 7,500 0.875 Appendage Resistance (% of bare hull) 10% Hull Resistance (Ibf) 20
In a hydraulics laboratory, a certain test liquid flows incompressible. For the flow of this liquid, it is correct to state that: Answers: a) The pressure must be the same at all points within the liquid. b) the velocity must be the same at all points within the liquid. c) the density must have the same value at all points within the liquid and cannot change as it flows. d) the pressure at a certain point within the liquid cannot change as it flows.
The dependence of thermal conductivity of a material on temperature is given by an empirical equation k = a ebT where a and b are constants, and k is in W/m-K and T is in K. Spot the true statement from the following set. a, a and b have the same dimension as k. b. a has the dimension of k and b is dimensionless. c. a and b are dimensionless. d. a has the dimension of k and b has the dimension of T.
Select the letter of the correct statement. Write the answer with calculations, drawing, rules or explanation 3- The Figure shown is the increase of both the fluid and surface temperature for flow in tubes which is heated: Entrance region Fully developed region A-) by water vapour, B-) by electric heater, C-) by chemical reaction, D-) Both of the A and B, E-) None of the above. (7, -T)
A Newtonian fluid with absolute viscosity (Greek mu) flows past a flat surface. Due to the no-slip boundary condition, the velocity profile, u(y), develops near the surface and is given by u/U (shown in image provided) where the constant parameters U and delta have dimensions of velocity and length respectively.a) Develop an expression for the shear stress acting in any horizontal plane.b) Determine the shear stress acting on the surface at y = 0 and again at the edge of the boundarylayer, y = delta. (Express your answers in terms of Greek mu, the outer velocity U, and the boundary layer thickness delta.)
Task 3: Fluid Mechanics Lab Meters You studied the SAYBOLT viscometer in the fluid mechanics lab to determine 20W50 Motor Oil viscosity. Follow the following steps to do your task. HEATING UNIT THERMOMETER LIQUID BATH Fluid CONTAINER CORK 60 CC- ŘESERVOIR Figure 4: Schematic for SAYBOLT viscometer.
Determine the resistance in each scenario presented. Explain whether the resistance is linear or not, and if not describe the relation, finally, explain how it can be linearized about a specific condition. Be sure to state the units and demonstrate that they are correct using the appropriate pressure/flow relation. a) Laminar flow An aqueous solution of 50% glycerol / 50% water is flowing through a pipe with the following system parameters: System_Parameters = (L = 100.0 D= 0.2 u= 0.022 p= 1150.0 9m=7.0 g = 9.81) units : L ~ m; D~ m; µ ~ Pa · s; p~ kg: 4. ~ 8: Confirm that this is laminar flow and then calculate the resistance. b) Pump Resistance from Pump Curve Consider the following pump curve: [Feet) (Meters] 30어 Find the pump resistance if the pump is supporting 15 meters of discharge head pressure, at a flow rate of 300 L/minute. 80- 250 7어 100 PSI L/min Determine the pump resistance in Pa 20어 6어85 PST 50 SCFM 5어 75 PST Note that standard pump curves are oriented opposite to the…
1. To determine the dynamic viscosity of a liquid you take repeated measurements of the liquid density and kinematic viscosity. These data are summarized in the following table: Avg. measurement Total Uncertainty P 999 kg/m³ ±0.5% V 1.23 mm²/s ±0.01 mm²/s kg Ns What is the dynamic viscosity? Give dynamic viscosity in units of; which is the same as ms 2. Determine the absolute and relative uncertainties in the dynamic viscosity.
Simple Machines-Levers, Inclined Planes, and Pulleys Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your Engineering Design journal. Remember to show all work. A lever has an effort arm that is 5 meters long and a resistance (load) arm that is 3.5 meters long. How much effort is needed to lift a 100 Newton weight? 5K i). Draw the figure representing the problem ii). How much effort is needed to lift a 100 Newton weight? iii). What is the Actual Mechanical Advantage 1. 5m i) AOON 5-5m
The U-Tube manometer is widely used to measure the difference in pressure between two containers or two points in a given flow system. As an example, a manometer connected between pipes A and B is shown determine the pressure difference in the two pipes. All dimensions shown are in centimeters. Kerosene Benzene Air PA 40 Pr 6. 20 14 Mercury Water L Add file Submit NEver submit passwords through Gocgle Forms.
In your new position at the fluid mechanics laboratory, you are required to do a to d branching. a) You perform a set of testing to measure the viscosities for various fluids: Engine oil, aluminum, zinc, water and 1:10 ratio of (corn starch: water). Pick and justify one type of viscometer for each type of fluid then, justify why a specific viscometer will not work for a type of fluid as follow: I would use I would not use Engine oil Aluminum Zinc Water Cornstarch solution Justify your answers in one statement each for each of the boxes in orange (total of 10 sentence b) For water you obtained the following data: Temperature [K] 300 310 318 340 Viscosity [cP] 0.8509 0.6913 0.5958 0.42 What is the viscosity of water at 290 K, 312 K and 350 K? You may use the following equation: ln ?? ???? = ?? + ?? . ???? ?? + ?? . � ???? ?? � 2 Where a = - 1.94, b = - 4.8, c = 6.74
TRUE OR FALSE 1.) In rheology, food materials of higher viscosity have higher resistance to flow. 2.) Specific heat is the amount of heat needed to raise the temperature of a unit mass of an object one degree higher without change of phase 3.) Surface area, is related to size but also depends on particle shape. 4.) Size can be correlated with weight given that the material has more or less uniform composition. 5.) Latent heat of fusion is the amount of heat that must be removed to convert water to ice and is also the same as the amount of heat added to convert ice to water.