QUESTION 9The steady sinking speed (in m/s) of the sphere isO a. 5.0O b. 6.9O C. 2.98'I'p O For Questions 5 - 9A smooth sphere of diameter d is dropped into a calm ocean. Data: d = 20 cm; Sphere material's density psp = 3000 kg/m3; Sea-water density psw = 1025 kg/m3, viscosity Psw = 1.002×103 Pa.s,temperature 20°C. B is buoyancy force on the sphere (numerical value only; no sign); similarly FD is the drag force on it, and W its weight; Cp is the drag coefficient. The sphere's steady sinking velocity isV (in m/s), assuming that the ocean is of sufficient depth such that V has been attained.Volume of a sphere of diameter d is Tid/6. Make other reasonable assumptions.

Name: QUESTION 9The steady sinking speed (in m/s) of the sphere isO a. 5.0O
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: QUESTION 9The steady sinking speed (in m/s) of the sphere isO a. 5.0O b. 6.9O C. 2.98'I'p O For Questions 5 - 9A smooth sphere of diameter d is dropped into a calm ocean. Data: d = 20 cm; Sphere material's density psp = 3000 kg/m3; Sea-water density

Given that, Diameter of sphere, d=20 cm,Density of sphere, ρsm=3000 kg/m3Density of sea water,…

Answered: A smooth sphere of diameter d is…

Engineering

Mechanical Engineering

A smooth sphere of diameter d is dropped into a calm ocean. Data: d = 20 cm; Sphere material's density psp = 3000 kg/m3; Sea-water density psw = 1025 kg/m³, viscosity µsw = 1.002×10¬3 Pa.s,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hydrodynamic journal bearing is subjected to 2000 N load at a rotational speed of 2000 rpm. Both bearing bore diameter and length are 40 mm. If radial clearance is 20 um and bearing is lubricated with an oil having viscosity 0.03 Pa.s, the Sommerfeld number of the bearing is
a band moves at a speed V and is in contact with a surface of an oil tank with viscosity m. calculate the power in watts required if the belt is moving at 2.9 m / s over SAW 30W oil at 20 C with L = 2m, b = 60m, Nu = 329.0mm ^ 2 / s, rho = 0.9g / cm ^ 2 and h=3cm
liquid (density 800kg/m3, viscosity 10−3 kg/ms) has to be supplied at a mean speed of 2m/s through a pipe of diameter 12.5mm with a surface roughness equivalent to that for structural steel. What is the magnitude of the pressure gradient necessary to achieve this flow? Your answer should have a positive sign and be to the nearest 10 Pa/m. You may wish to use the Moody diagram.
3.1 A cylindrical plug, 120mm long with a diameter of 95 mm, slides concentrically in a fixed cylinderwith an internal diameter of 95,2 mm. The radial clearance is filled with oil with a viscosity of 0.2 Pa.sCalculate the Force required to slide the plug along the cylinder at a speed of 5 m/s against the viscousresistance of the oil, the power lost due to the viscous resistance and the Kinematic viscosity of the oil ifits density is 850 kg/m 3 . A pressure intensifier is used in reverse deboost the pressure in a hydraulic system from 15MPa to7MPa. The volume of fluid required in the low pressure side is 700ml and the length of the stroke of thepiston is to be half the diameter of the low pressure piston. Calculate the diameters of the high-pressureand low pressure sides as well as the stroke length of the piston.
A balloon completely submerged in gasoline 80 cm in diameter (Figure P8.38) that weighs 0.5 N is filled with helium at 20 ° C at a pressure of 20 kPa. Ignoring the weight of the rope, calculate V if F equals: a) 80º (b) 70º(c) 60º (d) 50º
The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
Oil Coating: A long, continuous belt is pulled upwards through a chemical oil bath at velocity V0. The belt has rectangular cross-section and has length (L), width into the paper (W). The belt picks up a film of oil of thickness h, density ρ, and dynamic viscosity μ. Gravity g tends to make the oil drain down, but the movement of the belt keeps the fluid from running off completely. Assume fully developed, steady, laminar, incompressible and two-dimensional flow of oil to answer the following questions. Assume that no pressure gradient is needed in the vertical direction to drive the film flow. Also assume that the shear stress at the air-oil interface is zero (free shear condition). Assume no-slip condition for the fluid in contact with the moving belt. Justify any other assumptions you may make. Show all steps. (a) Derive an expression for the two-dimensional velocity field inside the oil film in terms of the known parameters. Clearly indicate your co-ordinates and origin. You must…
A ship 50 m long, with a wetted area of 800 m2, has the hullshape tested in Fig. There are no bow or stern bulbs.The total propulsive power available is 1 MW. For seawaterat 20°C, plot the ship’s velocity V kn versus power Pfor 0 < P <1 MW. What is the most efficient setting?
A space 22 mm wide between two large plane surfaces is filled with honey with absolute viscosity 0.16 N.s/m2 . What force is required to drag a very thin plate of 0.6 m2 area between the surfaces at a speed, v = 0.22 m/s(i) if this plate, t is equally spaced between the two surfaces? (ii) if t = 3 mm?
Diameter 60 mm, length-to-diameter ratio 1, bearing clearance 0.12 mm and radial load carried ISO VG100 oil is used in radial bearing with 8000 N rotation speed 1440 rpm. temperature is 40 ° C. Find the viscosity of the bed and the Somerfeld number.
Consider the displacement of oil by water from a capillary tube with radius of 25 microns. Assume viscosities of both fluids are 1 cp, the interfacial tension= 30 mN/m, velocity= 0.4 m/day Calculate the pressure drop between downstream (oil side) and upstream (water side) of the tube?