Problem 1 Given: Mass of canister: 4000 kg Mass of beam BD: 50 kg Max allowable force: 1. AB = 30 kN 2. CD = 30 kN 3. EF = 34 kN

Q: IF load : 100N and Effort force : 500N How can we calculate Fulcrum force?? Do anyone have a good…

A: GivenLoad=100NEffort force =500N

Q: A bench blast has the following drill hole parameters, diameter 200mm, bench height 10m, stemming…

A:

Q: Swivel flange center helps to permits the rod buckling due to compression or tensile shock forces.…

A: Answer: True The given statement Swivel flange center helps to permits the rod buckling due to…

Q: • Mechanically speaking, an oar is a beam, loaded in bending. • It must be strong enough to carry…

A: Given data Weight hung =W = 10 x 9.81 NDistance from Collar to point of maximum deflection = 2.05…

Q: the bending endurance limit for AISI 1080 steel shaft is Select one: a. 307.5 MPa. b. 250 Мра с. 450…

A: The bending endurance limit for AISI 1080 steel shaft can be given by - Se = 0.5×Ultimate strengthSe…

Q: Shown below is a figure of a landing gear configuration on the VS and VD planes (for landing gear…

A: The given figure shows the landing gear configuration on the VS and VD planes (for landing gear the…

Q: Can someone do a a static force analysis on this? Like method of joints sort of thing. Forgot how…

A: Static force analysis is done to do the analysis of the structure  and to check what will be the…

Q: Swivel flange center helps to permits the rod buckling due to compression or tensile shock forces.…

A: Gievn that    Swivel flange center helps to permits the rod buckling due to compression or tensile…

Q: Figure below shows a shaft that is loaded as given, l at points B and D to allow the shaft to…

A: In the given problem, Reactions will be determined by treating the beam to be in equilibrium and…

Q: ) What machine that has a shaft with a minimum of three (3) [bearings, pulley, sprocket, gear,…

A: given:

Q: Find out degree of freedom ?number of link ,joint, must be indicted like as link symbol L and Joint…

A: Given: To determine: no of joints No of link DOF

Q: True/false Q-5 Specific weight is an extensive property? If yes why ?

A: Specific weight is define as tge ratio of weight of the substance to its volume.  w• = W/v  W = mg {…

Q: How can we determine the displacement with truss?

A: Virtual work method: This method is a very important method which s used to find the slope as well…

Q: Can rigid motions be combined to give other rigid motions? If so, please name and draw me an…

A: Solution:

Q: )Which design do you recommend? and why?

A: A design should be chosen based on accessibility , ease of machining and logic. Therefore, the…

Q: A & D reactions? 6 kips/ft AB 9'-

A:

Q: A steel drum of a lifting machine has a mass of 25 kg, 2.4 m in diameter and 0.20 adius of gyration.…

A:

Q: Define the termTruss?

A: The truss is a structure that is used to distribute the load. It is made by combining members into…

Q: Explain Self-locking and over-hauling conditions for a power screw using sketch and its formula.…

A: Torque Requirement - lowering the load…

Q: What basic calculations would be made for the general problem statement: " cylinder pressure…

A: Concept: 1) Load resistance(R) will be the force (N).  2)The cylinder has a piston with…

Q: A four-wheel drive vehicle has a front solid drive axle suspension and a rear solid drive axle…

A: Solution: h = 20.5 in L = 108.5 in r = 15 in

Q: Define plain stress state with both words and schematic.

A: Plain stress: It is a two-dimensional (bi-axial) state of stress in which all stress acts in a…

Q: Write the methodology to quantify the " Work or Bond Index for crusher

A: The Bond work index is a measure of ore resistance to crushing and grinding and is determined…

Q: A significant disadvantage of using a flywheel with a reduced moment of inertia would most likely…

A: Given:   To select the correct option for the disadvantage of using a flywheel with less moment of…

Q: 3. A flange compressive coupling is used to connect a driving electric motor to a reduction gear box…

A: A flange compressive coupling is used to connect a driving electric motor to a reduction gear box of…

Q: Define the term Shaft Design?

A: Given Shaft design To find Definition

Q: Sketch the free-body diagram of the cylinder.

A:

Q: Problem # 4: The turbine motor moving at 378 rev/ min can produce 2.5 hp. The shaft diameter is 1.25…

A: Let T=Torque developed in the shaft d= diameter of shaft =1.25inches=0.03175m P = Power of…

Q: Make an illustration for this problem and label it completely. This lever has a fulcrum that they…

A:

Q: 1.2. Trucks are used to convey mineral from a stockpile to the metallurgical plant along a level…

A: Given: The total mass of the truck, M = 25 tonne the rolling resistance, R = 240 N/tonne The engine…

Q: %3D + be 'be %3D

A:

Q: Imagine two gears in mesh, the pinion is rotating clockwise, what is the force analysis for such a…

A: Explanation: The pinion is rotating clockwise and connected with the gear. Assume the gear us spur…

Q: An automobile has a brake horsepower output of 350 HP(horsepower) is designed to transmit power in a…

A: Given: Brake hoursepower=350 HP=350×746 W=261.1 KW Internal diameter→Di=3.5 inch=0.0254×3.5=0.0889 m…

Q: A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor…

A: Solution: Given Data: P=12 hpN=1150 rpmV=45 km/hd=12 inr=13 in   To Find: a) Calculate the effective…

Q: An open cylinder tank, D= 1.0m, h=1.5m, contain water at depth 1.0m. If this tank rotate about its…

A: Given data:

Q: discuss the principle of using elastic linear spring

A: Solution:

Q: Why are most of the loadings coplanar?

A: In the case of coplanar loadings system  The net force of the system is zero and The net moment is…

Q: Write a a short note on eccentric impact.

A:

Q: bolt tension force is 85% of its capacity. Use LRFD. cach) with a bolt spacing and gage distance of…

A: No of bolts = 8 Bolt dia d = 22 mm Bolt hole dia do = 25 mm Pitch distance p = 100 mm Gauge distance…

Q: How to solve SOLVING RIGID-BODY EQUILIBRIUM PROBLEMS?

A: The body is said to be in equilibrium when the net force and net torque acting on the body is zero.…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.