Problem 1: From the figure, determine the shear stress (a) at the junction between the flange and web and (b) at the neutral axis if the shear force is equal to 80 kN. OOR PLAN <- 120 mm I 20 mm 20 mm 160 mm 20 mm door

Problem 1: From the figure, determine the shear stress (a) at the junction between the flange and web and (b) at the neutral axis if the shear force is equal to 80 kN. OOR PLAN <- 120 mm I 20 mm 20 mm 160 mm 20 mm door

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Create a graph of the shear and bending stresses at the fixed support (B) over the cross- section.…

Q: For the given system: rods 1 (at both ends), d = 0.625 in and E = 15,000 ksi; rod 2, d = 0.375 in…

Q: A simply-supported beam with length, L= 10 m, is carrying a downward uniform load, w = 32 kN/m…

Q: DETERMINE THE AVERAGE PUNCHING SHEAR STRESS THE CIRCULAR SHAFT CREATES IN THE METAL PLATE THROUGH…

Q: For the frame shown, determine the maximum normal stresses (compression and tension) and the maximum…

Q: A wide-flange beam (see figure) is subjected to a shear force V. t- 0 Using the following dimensions…

A: Given t = 0.5 in h1 = 8.4 in Maximum shear stress = 6496.51 psi Minimum shear stress = 5414.99 psi V…

Q: The internal shear force V at a certain section of an aluminum beam is 6.9 kN. If the beam has the…

Q: eter of 40 mm. It is subjected to the force normal stress that acts at point A. answer to three…

Q: the largest axial P force that the given riveted joint can safely carry. calculate. Rivet diameter…

Q: Draw the V and M diagram of the beam. The cross section of the beam is a triangle with base 18 and…

Q: Given the cross-section of the beam shown. Show complete solution for the shear and moment diagram.…

A: To determine the flexural stress in topmost and lowest fiber of the beam at midspan. Given, Length…

Q: C- ODD: Assume that the axial load P = 40kN applied to the lap joint is distributed equally among…

Q: For the shaft loaded as shown, which point(s) at the section shown experiences the maximum shear…

A: Let's draw the FBD for first figure At the L shaft observe the stresses and their directions…

Q: A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN…

A: Given:- The magnitude of the force (P) = 4.5 kN The dimension variable (b) = 240 mm = 0.24 m The…

Q: 8 kips 4 kips 4 kips d, =2" 15 kips 15 kips d, =1.5" 20 kips !0 kips B d, =3" A

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

Q: Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum…

A: Compute the polar moment of inertia, J maximum shearing stress in any rivet does not exceed 80 MPa.…

Q: the largest axial P force that the given riveted joint can safely carry. calculate. Rivet diameter…

A: B = 340 mm t1 = 21 mm t2 = 38 mm Rivet diameter = 28 mm Shearing stress of rivet = 1400 kg/cm²…

Q: The continuous beam and post system shown below supports a 10 kip vertical load and a 5 kip…

A: The moment and shear force will act at point B. Moment and shear will be caused due to force of 5…

Q: if the maximum shear stress acting on rectangular beam is 50 N/mm, determine the average shear…

Q: A wooden beam is fabricated by bolting together three members. The cross-sectional dimensions are…

A: The given data is shown below: Diameter of bolts=11mms=170mmV=9.8 kNb1=29mmb2=27 mmd1=75 mmd2=350 mm

Q: The lap joint shown is fastened by five 34 inch-diameter rivets. The bearing stress in the plates is…

A: Given data : Diameter of rivets d = 34 in , Thickness of each plate is t = 12 in , Bearing stress…

Q: AT section has the dimensions given in Fig. ..Show that the neutral axis is 3 inches below the top…

A: Given data : INA = 166.7 in.4 Tensile stress at the bottom of the flange = 1000 psi This is a…

Q: 4.9 through 4.11 Two vertical forces are applied to a beam of the cross section shown. Determine the…

A: Given: Beam ABCD as shown in figure

Q: PROBLEM NO. 4. Determine the a) magnitude load P to be applied, and b) the normal stress on plane AB…

Q: The beam shown below has a cross section of channel shape with width b=400 mm and neight h=80 mm,…

A: step 1-

Q: The lap joint shown is fastened by five ¾ inch-diameter rivets. The bearing stress in the plates is…

Q: Calculate the normal stresses from the bending moment at the bottom point of cross-section C. Data:…

Q: For the truss and loading shown, determine the magnitude of the normal stress(in psi) in member CE,…

Q: 9-3. Determine the tensile stress in ea shown. Segment AB has a square cros Segment BC has a…

Q: PROBLEM 2 A flat bar of width b = 60mm and thickness t=10mm is loaded in tension by a force P. The…

Q: 1. Two plates are connected by bolts as F F 150 mr shown in the figure. Compute the bearing stress…

A: To calculate the bearing stress in each bolt of the given bolted connection. Given, Load acting on…

Q: 06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50…

Q: The beam shown below has a cross section of channel shape with width b3200 mm and height h=80 mm,…

Q: Compute the maximum shearing stress in MPa developed in the figure. (Round your answer to 2 decimal…

Q: With

Q: the AC rod suspended. The cross section of the AC rod is 15 x 8 mm2. 1.6 tons of force is applied to…

Q: AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume…

Q: The plate shown in the figure is fastened to the fix member by three 10 mm diameter rivets. Compute…

A: Given data The plate is fastened to the fix member by three 10 mm diameter rivets

Q: Subject : Mechanics of materials Give me right solution urgent please If the applied shear force V…

A: centroid of section: YBottom¯=7×2×(3+22)+2×3×2×327×2+2×3×2=2.846 inch Moment of…

Q: In the figure shown, assume that a 21.3-mm-diameter rivet joins the plates that are each 118 mm…

A: Lap joint: When one plate is overlapped on the other plate and both the plates are riveted by a…

Q: The section shown has dimensions H=1.4" & b=1.6", and is subjected to moments M1=6 in-kips & My=23…

Q: please answer asap

Q: 6.1 Along, round bar with a cross section 10 mm in diameter is used to hang a pipe. The max- imum…

A: The maximum allowed load on the bar and the cross sectional diameter is given. The maximum value of…

Q: termine the shear strain yxy at corners A, B, C, D i = dashed lines. Consider small strain…

Concept explainers

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.

Question

Problem 1: From the figure, determine the shear stress (a) at the
junction between the flange and web and (b) at the neutral
axis if the shear force is equal to 80 kN.
OOR PLAN
- 120 mm
I
20 mm
20 mm
160 mm
20 mm
FLOOR

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data about the problem

VIEW

Step 2: Calculation of shear stress at flange and web

VIEW

Step 3: Calculation of shear stress at neutral axis

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Explain in detail with figures( FBD) and in hand written
AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume P = 130 kN, w = 27 kN/m, a = 2.8 m, and b = 2.0m. Determine the magnitude and location of the maximum bending stress in the beam. A max = x = a i i B a → Pin |C * b W MPa m D a E
can someone help?
1.61.The state of stress at a point relative to an x, y, z coordinate system is given by 12 4 2 4 -8 -1 MPа -1 6. Calculate the maximum shearing stress at the point.
LAlogo_badge The allowable shear stress is Tallow = 9 ksi. (Figure 1) Figure Part A V 1 in. vec Submit VO VD ΑΣΦΙΚΗ 1 in. 3 in. Determine the largest shear force V that the member can sustain. Express your answer in kilopounds to three significant figures. Request Answer 1 in. 3 in. S < 1 of 1 C ? ( kip
Q3. Calculate the internal axial force in member AB, BE, BF and BC and state whether it is in tension or compression by using: a- The joint method. (refer to the course similar example) b- The section method ? c- Calculate the internal axial force in member CD and CF and state whether it is in tension or compression. Follow the method of your choice. d- Calculate the stress in MPa at the bars CD and CF if their cross section areas equal respectively to 2.0 cm² and 300 mm². 10KN *** 4m C A G 20KN 4m 10KN ** 4m 4m 8m
A double tee cross section is used for the beam shown below. Assume the following lengths and loads: a = 15 ft b = 8 ft C= 10 ft P= 12500 Ib Q= 5000 lb The moment of inertia of the cross section is i, = 110 in.". Determine the magnitude (ie, the absolute value) of the maximum compressive bending stress in the beam. TT 3.2 in. B D 5,8 in. Answer: Omax (Compression) = 1 psi %3D
Design the diameter of the pin for the hinge support if the allowable shear stress is 250 MPa. *DRAW THE FREE BODY DIAGRAM *COMPLETE SOLUTION *3 decimal places ALL ANSWER
4. The plate shown in the figure is fastened to thefixed member by seven 10-mm-diameter rivets.Compute the value of the loads P so that theaverage shearing stress in any rivet does notexceed 70 MPa.