Problem 1 ( forces of 1.5 kd 3.0 kN at points B and C respectively. The cross section of the beam is The simply supported beam shown below is subjected to two concentrated rectangular with a width of 48 mm and a height of 72 mm. The side view showing the cross section is also illustrated below. 1- Draw the shear force and moment diagrams of the beam. From the diagrams, determine the magnitude and location of the maximum bending moment and the maximum transverse shearing force. 2- Determine the moment of inertia of the cross section about the bending axis (neutral axis) 3- Calculate the maximum tensile and compressive stresses in the beam. 1.5 m 1.5 kN B 1.5 m 3.0 kN C 1.5 m 48 mm -TE I 72 mm

Problem 1 ( forces of 1.5 kd 3.0 kN at points B and C respectively. The cross section of the beam is The simply supported beam shown below is subjected to two concentrated rectangular with a width of 48 mm and a height of 72 mm. The side view showing the cross section is also illustrated below. 1- Draw the shear force and moment diagrams of the beam. From the diagrams, determine the magnitude and location of the maximum bending moment and the maximum transverse shearing force. 2- Determine the moment of inertia of the cross section about the bending axis (neutral axis) 3- Calculate the maximum tensile and compressive stresses in the beam. 1.5 m 1.5 kN B 1.5 m 3.0 kN C 1.5 m 48 mm -TE I 72 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM 5 Draw the FBDs, Shear, and Moment diagrams of the system shown below. What would be the maximum moment (magnitude and location) in the XZ plane, XY plane, and maximum moment overall (magnitude and location)? L₁ 12 in, L₂=6 in, F, = 300 lbf Z-Axis Y-Axis X-Axis O
The 1.5-in diameter solid steel shaft is simply supported at the ends. Two Pulleys are keyed to the shaft where pulley B is of diameter of 4 in and pulley C is of diameter of 8 in. Transverse shear stress needs to be considered. 1) Draw the bending moment diagrams of shaft AD for My and M₂, and indicate the location and the magnitude of the maximum bending moments. 10 in 200 lbf 1000 lbf 10 in 500 lbf 100 lbf 10 in F G E
Draw the shear force and bending moment diagrams for the beam with loading shown below, P= 16 kN, w= 30 kN/m, M=40 kN.m. Also, state the maxmium shear force and bending moment in the text box. (Upload the diagrams showing all key values with units as well as neat and clear calculations) P kN P kN w kN/m M KN.m A 0.5 m 1 m 1 m- 1 m- -1 m
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
Draw the shear and bending moment diagrams for the cantilevered beam below (figure not to scale). Identify the location and magnitude of max shear and bending stresses. 20 in 10 in 10 in 70 in 80 lbs 20 lbs 32.5 lbs
SHEAR AND MOMENT DIAGRAM PROBLEM 2 Use the AREA method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 6.9 ft, b = 10.4 ft, c = 5.8 ft, and w = 9.5 kips/ft. Label all significant points on each diagram and identify the maximum moments (both positive and negative) along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Determine the maximum shear force and bending moment in the beam. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. The roller at point D indicates that motion is restricted both up and down, and the beam will not lift off the roller. a B W b C D X
(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A.) (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Specify the values for key points on the diagrams. Wo A L
PART 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=2.0 m, PB = 2 kN, PC = 2 kN, and MB = 20 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. IMAGE* Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) IMAGE* PART 2 Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 3.5– m (i.e., just to the left of B)(c) x = 3.5+ m (i.e., just to the right of B)(d) x = 5.5– m (i.e., just to the left of C)When entering your answers, use the shear force sign convention.Answer:(a) V = ? kN.(b) V = ? kN.(c) V = ? kN.(d) V = ? kN. PART 3…
Q.2. Use the graphical method to draw the shear force and bending moment diaerams for the beam shown in figure (2). Label all significant points on each diagrams and identify the maximum moments along with their respective locations
The cantilever beam is loaded as shown in the figure. Derive the equations for the shear force (V) and the bending moment (M) for any location in the beam. Analyze the beam from the left, taking point A as the origin. 4 kips/ft 8 ft 8ft What is the moment (in kips-ft) at x = 4.00 ft? What is the shear force (in kips) at x = 5.50 ft? What is the moment (in kips-ft) at x = 13.00 ft? What is the behavior of V equation between points B and C? What is the behavior of M-diagram between points B and C?
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=14.0 ft, b=3.0 ft, c= 7.0 ft, w = 9 kips/ft and M = 300 kip-ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. " " Answers: Ay= Cy= b Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) i W i a W M a B M B ес b kips kips с Cy с X с -X
For the problem shown below (left), W = 51 lbs while L1 = 4.4 inches and L2 = 12 inches. This results in the shear force diagram as shown on the right, where A, is the reaction force in the vertical direction at point A. Based on this shear diagram, what is the maximum moment in the portion of the horizontal beam from x = O to x = L1 in units of lb-in to two decimal places. (Be sure to use a negative sign to designate a negative moment if necessary.) A |--L1-——————— L2 Ay lb 0 -Ay lb W L1 L2 W -L1- BO L1- -X