Problem 1: Determine the magnitude of the resultant force per meter length acting on the three-quarter cylinder gate. T 3 m R=3m

Q: A ruler is clamped clamped at weight 0-36 ку weight is at = deflection at deflection at It is x=17cm…

A: A ruler is clamped at x=3 cm and x=30 cm,Weight of 0.36 kg is concentrated at x=17 cmDeflection at…

Q: Tensile strength became. . when * .cohesive of particles absent ten five zero

A:

Q: Which stress element below correctly shows the normal and stress at point X? M T A G B D H Write the…

A:

Q: The parameter COD is: O a. Usually less in value than the ulitmate BOD b. Usually equal in value to…

A: The parameter COD is: a. Usually less in value than the ulitmate BODb. Usually equal in value to…

Q: Inercise:- a A cylindrical rod 100 mm 12 mm diameter of long with is subjected to a 30000 N. Assumiy…

A: To choose the suitable material that satisfies the given elongation and reduction in diameter…

Q: Can we use czmesh command with contact element to modeling debonding?

A: When czmesh command is used with elements with more than one stiffness no. then it shows an error.

Q: X A cylindrical part of diameter "d" is loaded in tension by a load "P" causing a stress: a-P/A. The…

A: Given, Uncertainty in load = ±15% Uncertainty in diameter = ±7.5% Uncertainty in stress = ±15%

Q: Determine the moment of inertia (in4) ĪY of the area shown with respect to the vertical line that…

A: To find moment of inertia about y axis

Q: For the truss shown on the figure, determine: Stress at element 4 if u3= 0.175 in and v3=0.5 in…

A:

Q: Then Tokn 83kn. sokn 83kn 16m 3m 3m c

A: One can also use calculator to solve the mentioned two equations.  It is two unknown with two…

Q: The piece of rubber is originally rectangular. Calculate the average shear strain Yxy at A if the…

A:

Q: ਕਰ ਸ Elementos TAB = TBC = TBD TAD = TDC = TED= 6m 135 kN B D ( ) ) 6 m 67.5 kN 1.5 m 1.5 m 1.5 m…

A:

Q: Massive thanks for answering in advance

A: The objective of the question is to calculate the location of the centroid, the second moments and…

Q: Briefly identufy what the requirement of strength is for a structural system and for a member of a…

A: Structural system- A structural system can be defined as the structure which helps in resisting the…

Q: A column (with initial dimensions x 150 mm, y 150 mm, and z 1000 mm) is confined by a rigid material…

A: Answer  we are given x = 150 mm y = 150 mm z = 1000 mm Pz = 150 KN G = 35 Gpa  v = 0.33 Calculations…

Q: Consider the following figure showing state of stress at a given point in a structural or nachine…

A: Solution: Given Data: σx=150 MPaσy=-100 Mpaτxy=50 Mpa (a) normal stress in x direction…

Q: Question 24 Which one of these microfibrillar angles in the illustration is expected to be stronger…

A:

Q: Can you recheck the plastic section modules here (Zx)

A: Determine the plastic section modulus of the section.

Q: Determine the stability and determinacy r C * r = || V C Classification

A: Draw the Free body diagram of the beam parts showing unknown reactions. Then count the number of…

Q: Use Virtual Work Method to answer the questions below considering the truss shown. Use the…

A:

Q: (c). Calculate the degrees of indeterminacy of the structures in Figure 3c. (Answers: degrees of…

A: Determine the degree of Indeterminacy of the structure

Q: Cg Methed f Sectins loo kw determine forces in FE, FC bC ノ

A: Hello dear this is the solution of your problem The answer is found to be Force in members…

Q: F cross section cut Ec, A Est, Ast

A: Given data: EstEc=6AstAc=19

Q: Determine the coordinates of the mass center of the welded assembly of uniform slender rods made…

A: Determine the coordinates of the mass center of the welded assembly of uniform slender rods made…

Q: The tip to tail addition of vector is also referred to as

A: The tip to tail addition of vector is also referred to as parallelogram law.

Q: Determine the coordinates of the mass center of the welded assembly of uniform slender rods made…

A: Determine the coordinates of the mass center of the welded assembly of uniform slender rods made…

Q: Determine the center of mass in y axis (y) of the homogeneous solid block. L = 0.45m 5L 4L 3L 2L 3L…

A: This question related to the Strength of Material.

Q: X. | Determine the location OF the centroid oF the composite figure shown.

A:

Q: The beam has a Young's modulus of Eo =100 GPa, a length of 1 = 4 m and 2nd moment of area of I₂ = 4…

A: Given: E = 100 GPa = 100 x 109 N/m2 Iz = 4 m4 l = 4 m w = 100 N/m

Q: Determine the load in each member if F = 150 lb Include FBD in your solution 12 5 A 50° 20° F B

A: Free body diagram  θ = tan-1 125θ = 67.38o ∑Fy = 0⇒-150 cos 20° + FAB cos 67.38° + FAC cos 50° =0…

Q: An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure.…

A: stresses on an element is given as followschange in length of diagonal BD=?

Q: ) Prove that stroctare is salee I Stakicalle dotaminate

A: Since the question number to be solved is not specified, the solution for subpart a is as follows:…

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 6)…

A: Given: The stress along the x-axis is 17 ksi. The stress along the y-axis is 20 ksi. The shear…

Q: (15 POINTS) The steel bar has the dimensions shown. Determine the maximum axial force P that can be…

A:

Q: The thin uniform plate shown has a mass of 100 kg and is subjected to a force and couple moment…

A:

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.