The plane rectangular gate can pivot about the support at B. For the conditions given, is it stable or unstable? Neglect the weight of the gate. Justify your answer. FLUID STpivot about the suppoane rectangular gate canmditions given, is it stable or unstable? Neghe gate. Justify your answer with calculationsWaterGate8 mB 45°APROBLEM 3.703.5 m

We can draw a free body diagram for given condition:Where,G = centroid of the gateP = center of…

Answered: FLUID ST pivot about the suppo ane…

FLUID ST pivot about the suppo ane rectangular gate can mditions given, is it stable or unstable? Neg he gate. Justify your answer with calculations Water Gate 8 m B 45° A PROBLEM 3.70 3.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1500 N 1.5 m D E

A: The segment AG is considered for analysis. The BC has had two members. The reaction at C is…

Q: solve the differential equation of the deformation of the beam below.

Q: (a) Calculate the shear equation V (x) and the moment equation M(x) as a function of the length L…

A: To determine:(a) Shear force and bending moment equations(b) Verify V(x)=ddxM(x) and verify the…

Q: The 36-kg homogeneous smooth sphere rests on the 26° incline A and bears against the smooth vertical…

Q: A rigid rod AB is attached to a hinge at 4 and to a spring with stiffness Eat D. The critical…

A: Rigid rod AB attached to spring at D

Q: Answer fast

A: To solve this problem using the stiffness method, we need to calculate the force in member BC and…

Q: The simply supported beam is subjected to the force F-550 N and the uniform distributed load with…

Q: Replace the three forces with an equivalent force-couple system, with the force acting at O. 280 N…

A: To find equivalent couple force system action at O

Q: Find the maximum force P (in N) that can be applied to block A without causing both blocks to move.…

A: Find the maximum force P (in N) that can be applied to block A without causing both blocks to move.

Q: Determine the forces in each members of 40 EN 3 m the truss loaded as shown. Tabulate the results…

Q: Solve the resultant of the given concurrent forces.Given angle = 30 degrees

A: From the given question it is required to determine the resultant of the given concurrent forces.

Q: Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force (P) is…

A: Given Specific gravity of oil=0.82 To find P

Q: 2. a) Draw a FBD and solve the support reactions of the pictured T-frame AED. b) Solve the internal…

Q: A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has…

A: Given: The vertical displacement is given by, wx=FEIyx448-L2x28+L42 The modulus of elasticity is…

Q: The force that will balance the resultant force is called equilibrant. It has the following…

A: Ans is (b)

Q: Determine the degree of indeterminacy. *

A: It is required to determine the Degree of Indeterminacy of the following frame:

Q: Example 2: Determine the force in each member of the truss. Assume the members are pin connected at…

Q: The sphere at A is given a downward velocity vo of magnitude 6 m/s and swings in a vertical plane at…

Q: X N/m Y N/m B Am В m 1. What is the total resultant vertical load in the beam AB 2. At what distance…

Q: A. The resultant of the four belt tensions and couple C is force R acting through points O. 1. What…

A: Moment about OMO=1000(0.45)+200(0.3)-800(0.3)-400(0.45)Mo=C=90 N-m

Q: Q2) ACED frame is pinned at C and support by two identical wires at A and B. The two wires have…

A: Given ACDE frame E=70 GPaA=250 mm2=250×10-6 m2α=23×10-6 1/C

Q: 4. A planar truss that is supported by a rolling pin support at point I and a fixed pin support at…

Q: Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on the…

A: Given data in question Vertical point loads Cantilever beam Span member length To find out…

Q: The truss shown is supported by a hinge at A and a roller at B. A load of 2500 lb is applied at C.…

Q: The uniform beam has a mass of 57 kg per meter of length. Determine the reactions at the supports. A…

A: Reference : Structural Analysis To determine : Reactions at A and B

Q: A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze[E =…

A: To determine the stress in the bronze rods (1) and the steel rod (2). Given, Modulus of…

Q: If two forces, acting at a point are represented by two sides of a triangle taken in order, which of…

Q: A tapered bar AB of solid circular cross section and length Lis supported at end B and subjected to…

Q: Please answer part C A = 150mm^2 E = 200GPa

Q: Find the value and direction of the resultant of the concurrent forces shown in figure.

A: Given data F1 = 100KN makes angle with horizontal = 30ο F2 = 20KN F3 = 30KN and F4 = 10KN

Q: The uniform beam has a mass of 41 kg per meter of length. Determine the reactions at the suppor y

A: to find support reaction at point A and B

Q: 5.Value of moment at the midspan of the beam in Ib-ft. b=2.27 inches h=4.24 inches P= 1968 Ib A= 4.5…

A: Draw the free-body diagram of the beam.

Question

The plane rectangular gate can pivot about the support at B. For the conditions given, is it stable or unstable? Neglect the weight of the gate. Justify your answer.

FLUID ST
pivot about the suppo
ane rectangular gate can
mditions given, is it stable or unstable? Neg
he gate. Justify your answer with calculations
Water
Gate
8 m
B 45°
A
PROBLEM 3.70
3.5 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

F1 F2 b M a C A a a Given the system above, F1 = 34 N, F2 = 96 N, M = 245 N-m, a = 3 m, b = 2 m, and a = 40°. %3D (a) Represent the system using a single force. Determine the magnitude of the force and its location relative to point A. Round all answers to the nearest integer. The magnitude of the force (N) is: N The position of the force relative to A (m) is: m (b) Represent the system using a force and a couple moment acting at point C. Determine the magnitudes of the force and the couple moment. Round all answers to the nearest integer. The magnitude of the force (N) is: N The magnitude of the couple moment (N-m) is: N-m
Please include free body diagrams. Need asap
solve correctly and show the complete solution.
2. A force system is shown below. Substitute: B=465, C= 9, E= 22, F=2060 F+E_kN 55KN 30KN 3 40 JE 30 B+C _kN a. Determine the component of the resultant along the u-axis. b. Determine the component of the resultant along the v-axis.
A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE, that exert uniformly distributed upward loads as shown. Determine the values of wec and WDE corresponding to equilibrium when WA = 750 N/m. 1200 N/m 20 C WBC ADA A 0.6 m- B' 0.8 m The value of WDE is The value of wBc is [ -3.1 ms -6 m- N/m. N/m. D (DE 1.0m E F
Linear Systems and Design Decisions Consider the structure in Figure 1. We will study the forces in the bars of this structure for various r. Develop the equations of static equilibrium and write them in matrix form. Take F2 N. The stiffness matrix A should be in terms of 2. Hint: The supporting structure at E is a pin and at D is a roller, the load on A is F and on B is. The length of member ED is 1m and of AD is 2m, variable z represents the length of member BD and CE. E in D 2m
From the following armor, determine the following: Reactions in A and F. The internal forces at node C. (Indicate whether the forces are in compression or tension.) The internal forces in the elements CH, CD and HI. (Indicate if the forces are in compression (C) or tension (T)). Draw the respective free-body diagrams. Consider the following: A and F are supports. the angles a, B, y are angles of 90, 60 and 30 ° respectively (Check image pr2 for the image of the armor) (Check image pr2.2 for the values to be used)
Solve force in AB & B C 0 =35° B = 40° 1 A B B 10 kN
Four balls of equal radii form a pyramid supported by a smooth horizontal plane surface. The three lower balls are held together by an encircling string as shown. Determine the tensile force S in this string if the weight of each ball is 1000 N and the surfaces of the balls are perfectly smooth. Neglect any initial tension that may be in the string before the top ball is placed upon the other three.
Please solve it fast. Within 20-30min
Current Attempt in Progress Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. A 66 49° 12° W Answers: AB = i W AC = i W BC = i W
5 The resisting area of the body against be aring stress is perpendicular to the orient ation of the force.( O False 6 True Axial force is also known as normal stres S.( 7 True False Compression is an axial deformation. True False