Batu Pahat district has an area of 1872.56 km2 with current population 495,338 residents. The signal to interference ratio S/I is 18 dB, path loss exponent, n is 4 and there are 6 co-channels cells in the first tier. Assume the whole district area is covered with constant cellular cell size of 2 km2, calculate; (i) The cluster size, N. (ii) The number of clusters available to cover the whole Batu Pahat district. (iii) The number of user that able to communicate simultaneously in a cell if the telecom provider has allocated 25 MHz duplex spectrum bandwidth, 200 kHz duplex channel bandwidth and one channel share with eight users. (iv) The number of users that can be supported in a cell based on the answer obtain in Q1(b)(iii). Given Grade of Service (GOS) is 2% and traffic intensity per user is 0.1 Erlang. Please refer to APPENDIX A. (v) The number of subcribers can be served in a Batu Pahat district. (vi) The market penetration of the designed network. Probability of Blocking 0.02 0.01 0.005 0.002 0.001 10 0.1 0.1 10 0.05 Number of Trunk Number of Trunked Channels (m) 1.0 10.0 Traffice Intensity in Erlangs (A) 100.0 APPENDIX A Figure A: Erlang B Chart

Batu Pahat district has an area of 1872.56 km2 with current population 495,338 residents. The signal to interference ratio S/I is 18 dB, path loss exponent, n is 4 and there are 6 co-channels cells in the first tier. Assume the whole district area is covered with constant cellular cell size of 2 km2, calculate; (i) The cluster size, N. (ii) The number of clusters available to cover the whole Batu Pahat district. (iii) The number of user that able to communicate simultaneously in a cell if the telecom provider has allocated 25 MHz duplex spectrum bandwidth, 200 kHz duplex channel bandwidth and one channel share with eight users. (iv) The number of users that can be supported in a cell based on the answer obtain in Q1(b)(iii). Given Grade of Service (GOS) is 2% and traffic intensity per user is 0.1 Erlang. Please refer to APPENDIX A. (v) The number of subcribers can be served in a Batu Pahat district. (vi) The market penetration of the designed network. Probability of Blocking 0.02 0.01 0.005 0.002 0.001 10 0.1 0.1 10 0.05 Number of Trunk Number of Trunked Channels (m) 1.0 10.0 Traffice Intensity in Erlangs (A) 100.0 APPENDIX A Figure A: Erlang B Chart

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. A carrier with a frequency of 20 MHz and amplitude of 20V is amplitude modulated y an audio signal of 10KHZ frequency and 5V amplitude a. Estimate the depth of modulation b. What is the upper side frequency (in MHz) c. What is the amplitude of the lower side frequency in (volts)
We have a baseband channel with a 1-MHz bandwidth. What is the data ratefor this channel if we use each of the following line coding schemes? a. NRZ-L b. Manchester c. MLT-3 d. 2B1Q
Help with this please.
As an engineer, you are asked to evaluate a frequency-division multiplexing system that uses SSB-SC subcarrier modulation and FM main-carrier modulation. There are 20 equal-amplitude voice-input channels, each band-limited to 3.3 kHz. A 0.7 kHz guard band is allowed between channels. a) Determine the transmission bandwidth if the peak frequency deviation is 400 kHz. b) Comment on the degradation of channel no 20 compared with channel no. 1.
Q2: A modulating signal is used to modulate a carrier signal(AM modulation). Let Pr , Pc, Psa. PusB, PLSB and u are the total power, carrier power, side band power, upper side band power, lower side band power and modulation index respectively. Prove the following: a. Pc = Pr () c. Pusp = Pasa =) P, 2+m2. b. PsB = Pr %3D 2+m2 2 (2+m2
a) A Double-Sideband Amplitude Modulator is shown in fig. 1 V DC cos(2n x 2 x 105t) m(t) v,(1) Σ Figure 1
Q3: The bit stream 10110100, draw the sequence using following digital data formats : a)Unipolar RZ , b) RZ-AMI ,c)Dicode- RZ , d) Polar NRZ ,e) Bipolar NRZ, f ) Split Phase Manchester . * Note ( that the question relates to communication materials)
Compare the DSB-LC, DSB-SC and SSB amplitude modulation techniques with each other in terms Bandwidth efficiency, b. Power efficiency, c. Complexity of their demodulation design. Explain which technique is better considering the criteria given above with the reasons using block diagrams and/or mathematical expressions. a. of
Q7. Figure Q7 shows a modulated waveform v(t) in millivolts as a function of time t in nanoseconds. 1.5 1.0 0.5 - 0.0 -0.5 -1.0 -1.5 100 200 300 400 500 t/ns Figure Q7: Modulated waveform (a) Describe the modulation scheme. (b) What are the values of the carrier frequency and the modulation frequency? (c) What is the value of the modulation index? (d) What is the transmission efficiency (ratio of modulated to total power) in this example? (e) Sketch the spectrum of this modulated waveform indicating the relative magnitudes of the various spectral components. (f) Demodulation of this type of waveform is usually performed with an envelope detector. Describe the function of an envelope detector and sketch an example circuit. (g) What requirements on the values of the components of your envelope detector circuit are there for the successful demodulation of the given waveform? (h) Keeping the same carrier wave, the modulating wave in this example is substituted with a square wave of 50%…
Networking A digital signal is to be designed to permit 100 Mbps for a bandwidth of 10 MHz. Determine: (1) Number of levels (2) signal to noise ratio. According to Shanon Capacity