Prob. 4 The figure below gives a cross section of a concrete dam. The subsoil is anisotropic and has permeabilities kh = 0.8 x 106 in./sec and kv - 2.0 x 107 in./sec. Find the rate of flow beneath the dam per foot length of the dam. Assume N₁4, and Nd=8. 32 ft 3 f ZPROVINS h₂ الود Concrete dare FREMONS

Prob. 4 The figure below gives a cross section of a concrete dam. The subsoil is anisotropic and has permeabilities kh = 0.8 x 106 in./sec and kv - 2.0 x 107 in./sec. Find the rate of flow beneath the dam per foot length of the dam. Assume N₁4, and Nd=8. 32 ft 3 f ZPROVINS h₂ الود Concrete dare FREMONS

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4
Two Water flows from reservoir A to reservoir B through two pipes as shown below. Determine 1) thedischarge in the pipe, 2) the pressure at point P. Assume α = 1.0 at all locations and neglect any minor headloss
Assume that the width of the tank is equal to 1 m. Find force F1 and F2.
• Figure shows a heavy dam. • Find the total horizontal pressure and total vertical pressure of 1-m breadth of dam body. 18 m 26 m 8 m 6 m 4m 12 m
I need answer within 20 minutes please please with my best wishes
Moment (KN.m) 300 250 200 150 100 50 0 0 A Moment-Curvature Relation 0.01 0.02 0.03 0.04 0.05 0.06 0.07 Curvature (1/m) L b) Yield displacement (Ay). Ay= Calculate the following values: a) Yield Force (Fy) that will cause the system to yield at point A. Fy= c) Plastic displacement (Ap). Ap= Hint: Au Ap+Ay = Başka yönergeler almak için tıklayın For the cantilever beam system given, construct the relation between the force (F) and the displacement (A) of the free end. You need to transform the moment curvature relation given into force-displacement relation. Beam length: L = 3.5 m Plastic hinge length: Lp = 0.3 m Note: All the results are positive. F e) The ultimate (failure) force (Fu) Fu = d) Ultimate (failure) displacement (Au). Au= (m) 0.08 0.09 (m) F A ha Ay Au (KN) (Write 2 digits after the decimal point) (m) (Write 4 digits after the decimal point) (Write 4 digits after the decimal point) (Write 4 digits after the decimal point) A (KN) (Write 2 digits after the decimal point)
The angular velocity wac = 5.6° per second. Determine the angular velocity of the hydraulic actuator BC in deg/s. L = 1.38 m 2L2 = 1.15 m 2L2 - Li --- L2 -
For a laminar flow through a channel, Reynold's number is given by 1500, what is the friction factor?
What is the density in the throat section? What is the area in the throat section? What is the velocity in the throat section?
Sssoon
3. Determine the resultant of the three forces acting on the dam shown in the figure and locate its intersection with the base AB. Required: Resultant and its intersection with the base AB Solution: P-10,000 lb -24,000 f F-6000 tb
The velocity in this channel is 0.9 m/sec. The Froude number is 6.73 m y=1.5 m 5 m 0.82 .a O 0.25 .b O None of these .c O 0.57.d O