Consider the concrete gravity dam shown in (Figure 1). The density of concrete is pc = 2400 kg/m³. The density of water is p = 1000 kg/m³. Suppose that ha = 24 m and b = 9 m. Figure ha h B < 1 of 1 Part A Determine the critical height h of the water level that causes the concrete gravity dam to be on the verge of tipping over. Assume water also seeps under the base of the dam and produces a uniform pressure under the dam. Hint. Work the problem using a 1-m width of the dam. Express your answer to three significant figures and include the appropriate units. h= 12.15 Submit 3 m C Previous Answers Request Answer ? X Incorrect; Try Again; 9 attempts remaining

Consider the concrete gravity dam shown in (Figure 1). The density of concrete is pc = 2400 kg/m³. The density of water is p = 1000 kg/m³. Suppose that ha = 24 m and b = 9 m. Figure ha h B < 1 of 1 Part A Determine the critical height h of the water level that causes the concrete gravity dam to be on the verge of tipping over. Assume water also seeps under the base of the dam and produces a uniform pressure under the dam. Hint. Work the problem using a 1-m width of the dam. Express your answer to three significant figures and include the appropriate units. h= 12.15 Submit 3 m C Previous Answers Request Answer ? X Incorrect; Try Again; 9 attempts remaining

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

Solve neatly and cleanly
Please answer part a, b
A syphon of diameter 200 mm connects two reservoirs having a difference in elevation of 15 m. The total length of the syphon is 600 m and the summit is 4 m above the water level in the upper reservoir. If the separation takes place at 2.8 m of water absolute, find the maximum length of syphon from upper reservoir to the summit. Take f= .004 and atmospheric pressure = 10.3 m of water.
Problem 8: EGL and HGL (IV) Consider a storage reservoir with a water surface elevation of 270 m. It is connected to a closed conduit (i.e., a pipe) that carries water down to a turbine at elevation 60 m. The friction head loss in the conduit is 20 m. Part A At point D, what are the pressure head P/y, the elevation head z, and the HGL? Part B Copy the diagram below. If the conduit is a closed pipe flowing full, is the velocity head V²/(2g) constant D→E? Answer yes or no, then sketch the EGL above the pipe D-E. Use a solid line. D E z = 270 m T Part C Based on your answer to Part B, sketch the HGL from D-E. Use a dashed line. z = 270 m Part D Now assume the conduit is an open channel. Copy the diagram below. Is the velocity head V²/(2g) constant D→E? Answer yes or no, then sketch the EGL above the pipe D→E. Use a solid line. E D z = 60 m T z = 60 m Part E Based on your answer to Part D, sketch the HGL from D-E. Use a dashed line.
Q4. 30 m height water backs up behind a 36 m height concrete dam. Leakage under the foundation gives a pressure distribution under the dam. The base width of the dam is 20 m. Determine the friction coefficient between the dam body and the foundation (Yconcrete 2.4 tm3). Check whether the dam would tip over at point A. 36 m 30 m reservoir A 20 m
Problem 3. The strength per meter of the longitudinal joint in the figure is 480 KN whereas the girth joint is 200 KN. Determine the maximum diameter of the cylindrical tank, if the internal pressure is 1.5 MN/m?. Longitudinal Joint Girth Joint:
Fluid
The gate AB shown in figure is hinged at A and kept closed by a force P at B. Compute for the Hydrostatic Force acting on the side of the gate AB. (Given: p = -18.46 kPa, OIL SG = 0.8)
SITUATION B. An open tank containing brine (SG = 1.3) is accelerated vertically at 7.5 m/s2. Determine the pressure: 6. 1.5 m below the surface if the motion is upward with a negative acceleration 7. 2 m below the surface if the motion is downward with a negative acceleration
• Figure shows a heavy dam. • Find the total horizontal pressure and total vertical pressure of 1-m breadth of dam body. 18 m 26 m 8 m 6 m 4m 12 m
A vertical circular sluice gate of 2 m × 3m sıze is used to cover an opening in a dam. On the upstream of gate, the liquid of relative density 1.50 lies up to a height of 6.0 m above the bottom of gate, whereas on the downstream side, the clean water is available 3.0 m below the top of gate. Apply the concept of Hydrostatic pressure to calculate: 1. The resultant force acting on the gate and the position of center of pressure. 2. The force acting at the bottom of the gate to maintain it in equilibrium. Assume that the gate is hinged at the top.
A dam is triangular in cross-section with the upstream face vertical. Water is flushed with the top. The dam is 8 m high and 6 m wide at the base and weighs 1.3 tons per cubic meter. The coefficient of friction between the base and the foundation is 0.8. Determine the maximum unit pressure in kPa on the foundation.