Prob. 2.6-8. The cylindrical rod in Fig. P2.6-8 is made of an- nealed (soft) copper with modulus of elasticity E= 17 x 10³ ksi and Poisson's ratio = 0.33, and it has an initial diam- eter do = 1.9998 in. For compressive loads less than a "criti- cal load" P., a ring with inside diameter d, = 2.0000 in. is free to slide along the cylindrical rod. What is the value of the critical load Por? P C -Ring P

Prob. 2.6-8. The cylindrical rod in Fig. P2.6-8 is made of an- nealed (soft) copper with modulus of elasticity E= 17 x 10³ ksi and Poisson's ratio = 0.33, and it has an initial diam- eter do = 1.9998 in. For compressive loads less than a "criti- cal load" P., a ring with inside diameter d, = 2.0000 in. is free to slide along the cylindrical rod. What is the value of the critical load Por? P C -Ring P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

answer as soon as soon as possible
2-) Consider the thin (steel) plate in figure given below. The plate has a uniform thickness t= 1 cm., Young's modulus E = 25 x 10° N/cm?, and weight density p= 0,2448 N/cm³. In addition to its self-weight, the plate is subjected to a point load P = 200 N at its midpoint. (Please be careful for the units.) (a) Model the plate with two finite element. 12 cm (b) Write down expressions for the element stiffness matrices and 18 cm element body force vectors. (c) Assemble the structural stiffness matrix K and global load 36 cm vector F.(' P =200N (d) Using the elimination approach, solve for the global displacement vector Q. (e) Evaluate the stresses in each element. ( -. X 6 ст
I need the answer as soon as possible
The axially aligned pressure vessel, shown in Fig Q2, is made from aluminium exhibiting a Young's Modulus of 73GPa and a Poisson ratio of 0.34. It has an outer diameter D, of 86mm and a wall thickness t of 5mm. The vessel is subject to an internal pressure P of 150bar and externally applied torque T of 4.5kNm. a) Draw the 2D planar state of stress of any finite element located on the outer surface of the pressure vessel, according to the polar coordinate system provided. b) Sketch the longitudinal, circumferential and planar shear strain profile through the thickness of the vessel wall. c) Determine the minimum factor of safety for the given load cases, assuming the aluminium has a yield strength of 175MPA, and comment on the most likely mode and locus of failure. theta i. - Z - T Do Section A-A: Side View End View
Please show intermediate steps including free diagrams, equations used, and problem setup, so that your approach can be followed
The L-shaped rigid bar shown is pin connected at C, welded to a rigid bar AB at point B, and rests on a composite bar at D. Rigid bar AB is attached to two identical rubber (G = 150 MPa) pads with the shown dimensions and having a thickness of 30 mm each. Meanwhile, composite bar DE is made of hollow aluminum (with outer diameter do and inner diameter di, E = 70 GPa) surrounding a solid steel rod (diameter = di, E = 200 GPa). Determine the maximum force P that can be applied to the rigid bar at B if the allowable normal stresses in aluminum and steel are 80 MPa and 200 MPa, respectively and the shear stress in rubber is 30 MPa.Use the following values:Parameters s = 135 mm x = 3.8 m y = 5.5 m do = 60 mm di = 35 mm
A cylinder with a piston diameter of 100 mm under apressure of 20 MPa exerts a force on the left end of a lever. Calculate the force obtained at the end of the lever? Answer: 40,000kN
'Uniform 60-kg bar AB is subjected to force P Smooth guides at B. At A, Mg = 0.8. (a) If P= 400 N, find fric- tion force at A. (b) Find Prequired to cause slippage at A. y BO 1/2 1/2 60° A P
A same circular plate with thickness of h-190mm is considered here again. The plate made from a material which its Young's modules and Poisson's ratio are E=60 GPa and V-0.22, respectively. Workout the value of flexural stiffness D in GN.m (GN.m3 10° N.m) (Hint: round your answer 4 digits after decimal point))? Ro