Prob. 2: Water at 20°C flows for 1 mi through a 3-in-diameter horizontal wrought-iron pipe at 0.557 ft'/s. Estimate the head loss and the pressure drop in this length of pipe.( take: p = 1.94 slug/ft and u = 2.09×10 slug/ft-s. and For wrought iron take ɛ=0.00015 ft.) %3D

Prob. 2: Water at 20°C flows for 1 mi through a 3-in-diameter horizontal wrought-iron pipe at 0.557 ft'/s. Estimate the head loss and the pressure drop in this length of pipe.( take: p = 1.94 slug/ft and u = 2.09×10 slug/ft-s. and For wrought iron take ɛ=0.00015 ft.) %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: )Water 10°c flows down through a 53.13 deg, nclined, converging pipe section as shown. The fiow…

Q: For the horizontal laminar internal flow through a pipe of diameter (d), if the veloci -1 dP (r)%3D…

Q: Fresh water at 20°C flows from reservoir A to reservoir B as indicated. Calculate the flow rate by…

Q: Consider a steady, fully developed flow in a horizontal pipe of diameter 80 mm. Over a section of…

Q: Water at 20°C flows through an inclined 8-cm-diameter pipe. At sections A and B, pA = 196 kPa, VA =…

A: Givend=8cmPA=196 kPaVA=3.5 m/szA=26.5mPB=280 kPazB=10.1mf'=4f=0.02

Q: A water jet washing system for galvanized steel profiles uses a series of n = 15 nozzles mounted on…

A: Given : To find : a) The total flow demanded from the compressor if a discharge velocity of not…

Q: Q5: A smooth pipe of diameter 400 mm and length 800 m carries water at volumetric flow rate 0.04…

A: Given data Diameter of pipe = 400 mm = 0.4 m Length of pipe = 800 m Volumetric flow = 0.04 m3/s…

Q: An oil with (s.g=0.85) and kinematic viscosity = 1.8x105 m²/s flows in a 10-cm diameter pipe at…

Q: In Fig. a thick filter is being tested for losses. Theflow rate in the pipe is 7 m3/min, and the…

A: Given: The flow rate in pipe, Q = 7 m3/min The upstream pressure in pipe, P = 120 kPa The diameter…

Q: 3. Water at 20°C is to be pumped from reservoir 1 to 2 in a 6-in-diameter asphalted cast iron pipe…

A: The power required by the pump to displace fluid from a place to another can be calculated using the…

Q: EXAMPLE 8: Water at 20°C (p = 998 and u = 0.001 Pa. s) flows in the 30 cm diameter plastic pipe in…

Q: Water at 20°C fl ows at 3 m3/h through a sharp-edged3- cm-diameter orifi ce in a 6-cm-diameter pipe.…

A: Given Data: The discharge rate is: Q = 3 m3/h The diameter of the orifice is: d=3 cm The diameter…

Q: Water is flowing at 40L/min in a 2 cm diamter pipe, 10 m long at 20 o C. Calculate whether the flow…

Q: Compute the head loss and pressure drop in 80 m of horizontal 150-mm-diameter asphalted cast-iron…

A: Detailed answer given in attached file kindly refer it.

Q: 3. Sketch the shear stress and velocity distribution for laminar flow across a pipe section.

A: Consider R to be the radius of the pipe. The expression for the velocity from the center of the pipe…

Q: Water at 25 deg C (998 kg/m 3 ) flows at 10 m 3 /s through a straight pipe of an ID of 1.38 m to 2…

A: Given data Density of water = 998 kg/m3Diameter at section 1 = d1 = 1.38 mDiameter at section 2 = d2…

Q: It is desired to deliver 60 m3/h of water at 20°C through ahorizontal asphalted cast iron pipe.…

A: Given: The length of the pipe is L=100 m. The pressure drop in the pipe is ∆P=40 kPa. The volume…

Q: Q5:Oil flows in a pipe 80 mm bore with a mean velocity of 5 m/s. The mean surface roughness is 0.02…

Q: A smooth pipe of 100 mm diameter and 1000 m long is carrying water at the rate of 10 litres/sec. If…

Q: Water at 200°C (p = 998 kg/m³, and m2/s flows through a horizontal pipe of diameter with a flowrate…

A: T=200Cρ=998kg/m3v=1×10-6m2/sD=0.1mQ=4×10-2m3/s∆pl=2.59 kPa/m To-Find:- 1. Thickness of viscous…

Q: Benzene (u=3.95 x10-4Pa-s) at 60°C is flowing in a 24.3mm steel pipe (absolute roughness =4.6 x10-5m…

A: Answer: The pressure difference between two points 100 m apart if the pipe is horizontal: ∆P =…

Q: A pump delivers 1 hp to a water at 68°F flowing in a 10-in-diameter horizontal, cast iron pipe at V…

Q: Water flows at 20°C through a new cast iron pipe at a velocity of 4.2 m/s. The pipe is 400 m long…

A: Given: Let us consider the given data, Temperature,T=20°C Velocity,v=4.2 ms Diameter, d=150 mm=0.15…

Q: SAE 10 oil at 20°C (γ = 8.52 kN/m , ρ = 860 kg/m , μ = 8.14 × 10 Ns/m ) is to flow through a300-m…

A: Given: The specific weight of oil, S = 8.52 kN/m3 The density of oil = 860 kg/m3 The dynamic…

Q: A 19-cm-diameter, 19-km long pipe is used to transport petroleum (u= 0.075 Pa s. p= 880 kg/m') at a…

Q: SAE 10 oil at 20° (ρ=869 kg/m³, μ=8.14 × 10-2 N•s/m²) flows in a 200 mm diameter pipe. Find the…

Q: SAE 10W oil flows through a 30-cm-diameter new commercial steel pipe 100 m long with a head loss of…

Q: The 20 m long pipe between the A and B tank in the figure is made of cast iron and its flow rate is…

A: Given: The length of pipe, L = 20 m The flow rate, Q = 0.002 m^3/s

Q: Give me both right solutios In circular pipe with 0.1 m diameter, pressure drop is 100 kg/m2 over…

Q: Laminar oil (u 0.1kg SG = 0.9) flows through a long, straight smooth 5 cm m.s diameter pipe at 14…

Q: Water (35degC) is flows through a pipe ( l = 80m ; d = 250mm ). The Reynolds no. = 450000. Assume…

Q: Water flows at a rate of 2.4f * t ^ 3 / s in an old, rusty 7.8-in.-diameter pipe that has a relative…

A: Given;

Q: Ethanol at 20°C flows at 125 U.S. gal/min through a horizontal cast-iron pipe with L=12 m and d= 8…

A: Given:Temperature of Ethanol, T=20oCEthanol flow rate, Q=125 US gal/min=12515850m3/s=0.0078864 m3/s…

Q: I need help correcting this part of the following problem, also include step-by-step solutions.…

A: Given data:

Q: A single looped network has to be analysed by the Hardy Cross method for given inflow and outflow…

Question

Prob. 2: Water at 20°C flows for 1 mi through a 3-in-diameter horizontal
wrought-iron pipe at 0.557 ft/s. Estimate the head loss and the pressure
drop in this length of pipe.( take: p = 1.94 slug/ft and u = 2.09x10
slug/ft-s. and For wrought iron take ɛ=0.00015 ft.)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

8
A laminar flow element measures low gas-flow rates with a bundle of capillary tubes packed inside a large outer tube. Consider oxygen flowing at 84 ft3/min in a 4-in-diameter pipe. (i) Is the flow approaching the element turbulent? (ii) If there are 1000 capillary tubes, Length L, is 4 in, select a tube diameter to keep Reynold’s number below 1500 and also to keep the tube pressure drop not greater than 0.5 lbf/in2. (iii) Do the tubes selected fit nicely within the approach pipe?
Problem 3 Water at 20 °C (p = 998 kg/m³ and v= 1.004 x 10-6 m²/s) flows through a horizontal pipe of 0.1-m diameter and 2 km long at an average velocity of 4.0 m/s. Suppose the friction coefficient at the pipe is f = 0.022. (a) Calculate the flow rate. Is the flow laminar or turbulent? (b) What is frictional head loss? (c) Determine the friction velocity and the thickness of the viscous sublayer. (d) Determine the centerline velocity and the velocity at 0.025 m above the pipe wall (point A). D 0.1 m A 0.025 m
A SAE 30 oil at 38°C flows through a 0.01-m diameter, with a 4-m long pipe which is inclined at a 31-degree angle at a flow rate of 0.18 L/s (1000 L = 1 m3). Estimate the pressure loss (in kPa) across the pipe.
What’s the answer for this please ?
60m 44m (2) (1) (3) 40m (4) 40m (5) 42m c) Find the flow discharge within the system. (6) 30m 35m Q (2). You have a tank open at the top, flow in the 25-cm-smooth-65 m long- plastic pipe. (7)
Find the related Average Nusselt number equation
(2) It is desired to deliver 60 m'/hr of water at 20°C through horizontal asphalted cast iron pipe. Estimate the pipe diameter d that will cause the pressure drop to be exactly 40 kPa per 100 m of pipe length. Take water density p Solve this problem iteratively using either Moody chart or the Colebrook equation. 998 kg/m and dynamic viscosity µ = 0.001 kg/(m.s).
with a head loss of 7.5-m. Use iterative method to find the pipe diameter requires to keep a flow Q3: Oil, with (p- S950 kg/m'; v 2x10s m2/s), flows through horizontal smooth pipe of 80-m long rate of 0.332 m/s steadily flowing, (Start with initial guess of friction factor f-0.01)
Q3) EthanoL at 20c°( P= 789 Kglm², M=00012 125 gpm through I52/mis) flow at horizon tal easta iron pipe with L= 12 m a and d=5cm, Neglecting entrance effect estimaite A- the wal shear stress 3- the precent reduct ion in friction factor if the pipe walls are poli shed to a smooth surface.? (1-2)