Ethanol at 20°C flows at 125 U.S. gal/min through a horizontal cast-iron pipe with L=12 m and d= 8 cm. Neglect entrance effects. For ethanol, take p=789 kg/m³ and μ = 0.0012 kg/m s. For the given flow take Moody≈ 0.0282 and smooth 0.0187.

Ethanol at 20°C flows at 125 U.S. gal/min through a horizontal cast-iron pipe with L=12 m and d= 8 cm. Neglect entrance effects. For ethanol, take p=789 kg/m³ and μ = 0.0012 kg/m s. For the given flow take Moody≈ 0.0282 and smooth 0.0187.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A smooth plastic pipe is to be designed to carry 10 (ft^3)/s of water at 20°C (68°F) through 1750 ft of horizontal pipe with an exit pressure at 20 psig. The pressure drop is approximately -280 psig. Estimate the pipe diameter (in inches) that will result in the given pressure drop. For water at 68°F: ρ = 1.94 slug/(ft^3), and μ = 2.09E-5 slug/(ft-s).For the above sizing problem, if the pipe material has an allowable stress of 7500 psig, what is the minimum pipe schedule?
It is designed in such a way that the internal temperature of a commercial heat treatment furnace can reach up to 165 oC. All surfaces of the furnace consist of firebrick (10 cm), insulation material and sheet metal (3mm) from the inside out. Given that the outdoor temperature is 22 oC, the outer sheet will be allowed to go up to 35 oC, which is a temperature that will not disturb in contact with hands. In this case, determine the insulation material thickness to be used. The thermal conductivity coefficient of the insulation material is insulation 0.066 W / m oC, 60 W / m oC for sheet metal and 115 W / m oC for firebrick. Indoor heat transfer coefficient will be accepted as 25 W / m2 oC and 12 W / m2 oC for outdoor environment.
Problem 3 Water at 20 °C (p = 998 kg/m³ and v= 1.004 x 10-6 m²/s) flows through a horizontal pipe of 0.1-m diameter and 2 km long at an average velocity of 4.0 m/s. Suppose the friction coefficient at the pipe is f = 0.022. (a) Calculate the flow rate. Is the flow laminar or turbulent? (b) What is frictional head loss? (c) Determine the friction velocity and the thickness of the viscous sublayer. (d) Determine the centerline velocity and the velocity at 0.025 m above the pipe wall (point A). D 0.1 m A 0.025 m
help
What’s the answer for this please ?
Water flows in a pipe B of diameter 25 cm, with a uniform velocity of U2 = 2.5m/s. Liquid pesticide (assume SG =1) is injected into the flow steadily and without friction at A (diameter 5-cm), with velocity that has a profile given by vmax/D^2· (D.r-r^2), where r (in m) is the spanning coordinate measured from the centerline of the pipe., as illustrated. The two fluids start mixing and are fully mixed at C. Then the fluid is sprayed using a 500 2-mm holes showerhead. The showerhead is inclined at an angle 0 = 45°. Ignore pressure differences. For vmax = 3, what is the exit velocity through each hole? Mixing region Fully mixe Inlet A U2 C Not to scale B
Water enters at section 1 at 10 m/s with sp gr of 0.998 and alcohol enters sections 2 at 6 m/s with sp gr of 0.8. Pipes 1, 2 are of 3 cm in diameter and pipe 3 is of diameter 4 cm. Compute the exit velocity and density of the mixture. Assume ideal mixing of incompressible fluids. Please provide complete solution
Show work for both subparts as it is a single problem.
What is the total force acting on a 90 degrees pipe bend if the flow pressure is 3 x105 Pa, the flowrate is 0.1m3/s and the specific gravity of the fluid is 0.7. The pipe diameter is 10cm and the weight of the fluid can be neglected (remember to consider both force components).